.jpg)
Parts & Supplies | Pick and Place/Feeders
> FUJINTAI TECHNOLOGY CO.,LTD JUKI E9572729CA0 LA (L) CABLE ASM. www.fujintai.com JUKI E95737290A0 MTC I/F(L) CABLE ASM. FUJINTAI TECHNOLOGY CO.,LTD JUKI E95738550A0 DISPESE SV ASM www.fujintai.com JUKI E95747210A0 BAD MARK SENSOR CABLE ASM. FUJI
Parts & Supplies | Pick and Place/Feeders
> www.fujintai.com JUKI E9621715000 CAMERA NO.11 LENS FUJINTAI TECHNOLOGY CO.,LTD JUKI E9621727000 Z/THETA CTL CABLE www.fujintai.com JUKI E9621729000 YC 1 SHAFT DRIVER FUJINTAI TECHNOLOGY CO.,LTD JUKI E9621739000 TWISTED PAIRED CABLE (5M) www.fu
4.jpg)
Parts & Supplies | Pick and Place/Feeders
> www.greensmt.com JUKI E9572729CA0 LA (L) CABLE ASM. SHENZHEN GREEN TECHNOLOGY CO.,LTD JUKI E95737290A0 MTC I/F(L) CABLE ASM. www.greensmt.com JUKI E95738550A0 DISPESE SV ASM SHENZHEN GREEN TECHNOLOGY CO.,LTD JUKI E95747210A0 BAD MARK SENSOR CAB
41.jpg)
Parts & Supplies | Pick and Place/Feeders
> www.greensmt.com JUKI E9572729CA0 LA (L) CABLE ASM. SHENZHEN GREEN TECHNOLOGY CO.,LTD JUKI E95737290A0 MTC I/F(L) CABLE ASM. www.greensmt.com JUKI E95738550A0 DISPESE SV ASM SHENZHEN GREEN TECHNOLOGY CO.,LTD JUKI E95747210A0 BAD MARK SENSOR
Parts & Supplies | Pick and Place/Feeders
> FUJINTAI TECHNOLOGY CO.,LTD JUKI E9572729CA0 LA (L) CABLE ASM. www.fujintai.com JUKI E95737290A0 MTC I/F(L) CABLE ASM. FUJINTAI TECHNOLOGY CO.,LTD JUKI E95738550A0 DISPESE SV ASM www.fujintai.com JUKI E95747210A0 BAD MARK SENSOR CABLE ASM. FUJI
Electronics Forum | Wed Jan 17 21:02:48 EST 2007 | Jnet
If you are just wanting a replacement blower for your air crossflow cooling section. You should be able to purchase through Electrovert cheaper than $1600 dollars. Someone must have quoted you more than just a replacement blower.
Electronics Forum | Mon May 20 15:25:13 EDT 2013 | smtventasmex
Hi i can help you with your blowers needs contact me at vhmaderoATsmtvys.com
Electronics Forum | Tue May 07 09:26:38 EDT 2013 | emeto
Hello knowledgeable people, we have Omniflow 10Zone oven from 3-4 years and we changed over 20 blowers. The blower is German and I think is a very good quality(quite expensive too), but still keep getting bad. Does anyone have similar problem? Do yo
Electronics Forum | Wed May 22 12:59:09 EDT 2013 | cyber_wolf
That sounds very odd what smter is saying. The screws around the outside of the fans have nothing to do with the bearings. You only really need to tighten those screws enough to squish the gasket a little. No special torque settings required. As lon
Electronics Forum | Tue May 07 09:42:17 EDT 2013 | cyber_wolf
We bought a "very used" Omniflow 10 at least ten years ago. We have only replaced maybe 5 blowers in that time.
