Industry Directory | Consultant / Service Provider / Distributor / Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
Industry Directory | Manufacturer
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
High Precision Dispensers - MAX Series (Non-Heated) Max Series is capable of a wide variety of dispense applications including MicroVolume, Solder Paste and Conductive Adhesive, Underfill, Surface Mount Adhesive, Dam and Fill, Encapsulations, LED En
New Equipment | Board Handling - Conveyors
Model No: KSUN 250 Automatic Sucking Loader PCB loading time: Approx 6seconds Magazine change-over time: Approx 30 seconds Power supply: 100-230V AC (customized ), single phase, MAX 300V/A Air pressure: 4-6 bar, MAX 30L/minute Transport height:
Electronics Forum | Wed May 25 19:04:39 EDT 2005 | russ
check your clamping rails and see if you see any little wear marks, we constantly hit these clamps during placement when the parts are too close to the edge. The height of that clamp is either 4 or 6mm I beleive and the noozles will hit them on occ
Electronics Forum | Tue May 29 08:37:52 EDT 2018 | bukas
screen alignment chase clamp state is ON, it can be turned OFF but when I get out of diagnostics machine turns them ON again. Tooling is set to magnetic, and on other machines I have chase clamps are not energized all until board is in machine and st
Used SMT Equipment | SMD Placement Machines
* DOS * Flying Nozzle change * Fiducial camera * Pneumatic tape feeder * Locate Pin * Edge clamp * Z servo push plate * Entrance sub stop * Exit sub stop * Auto width adjust * Feeder float detection
Used SMT Equipment | Screen Printers
2003 DEK Horizon 01 Screen Printer *** Note: This lot contains two items. (1) DEK Horizon 01 Screen Printer (1) DEK VF35 Vacuum System Approx Dimensions: 70" x 70" x 68" Location: Jasper, IN USA Serial: 281505 Features: o Advantec 2.05 Computer syste
Industry News | 2003-03-17 09:40:03.0
Omnimate BLZ/BLZF 5.08F PCB connectors have integral screwed flanges to ensure safe and secure connection under the most severe vibration conditions.
Industry News | 2003-05-19 08:44:19.0
Two new PCB power connectors offer easy high power wiring (up to 54A) with built-in safety features to prevent incorrect connections and resist strong vibration.
Parts & Supplies | Pick and Place/Feeders
LEVER CLAMP Part Name：LEVER CLAMP Part No：GPC7012,MCA0191
Technical Library | 2010-05-06 18:46:29.0
Stencil printing technology has come a long way since the early 80’s when SMT process gained importance in the electronics packaging industry. In those early days, components were fairly large, making the board design and printing process relatively simple. The current trend in product miniaturization has led to smaller and more complex board designs. This has resulted into designs with maximum area utilization of the board space. It is not uncommon, especially for hand held devices, to find components only a few millimeters from the edge of the board. The board clamping systems used in the printing process have become a significant area of concern based on the current board design trend.
Technical Library | 2016-08-24 06:15:35.0
From consumer electronics to systems control, automotive technology to aviation and aerospace – today, electronics are absolutely essential in many sectors. They increasingly replace mechanical components, eliminating wear and tear and thereby extending the service life. What is easily forgotten in this regard is that electronics are also subject to the laws of mechanics. Mechanical test equipment is crucial to test components for the secure hold of welded, soldered or adhesive bonds. A new, mechanically intricate test probe with universal clamping jaws, that can even grasp the individual bonding wires, is in line with the trend toward ever smaller components. Serving as an actuator for these is a micro drive that can be precisely controlled using a miniaturised motion controller to relieve the control unit in the test device.
High Precision Dispensers - MAX Series (Non-Heated) Max Series is capable of a wide variety of dispense applications including MicroVolume, Solder Paste and Conductive Adhesive, Underfill, Surface Mount Adhesive, Dam and Fill, Encapsulations, LED En
J7065407B CLAMP LEVER 1 J2500273 CLAMP SPRING PIN 1 J2500231 PIN 7 J2500315 CLAMP LEVER 2 J2500231 PIN 7
Career Center | Torrington, Connecticut | Engineering,Management,Production,Quality Control,Sales/Marketing,Technical Support
MECHANICAL AND ELECTRONIC CAD TECHNOLOGY-CERTIFICATION • TECHNICAL DRAFTING: Equipment Use, Orthographic Projection, Dimensioning, Auxiliary Views, Fasteners, Manufacturing Processes and Fits and Tolerances • POWER TRANSMISSION/ANSI 14.5 1994: Bearin
Career Center | , District of Columbia | Engineering,Management,Production,Sales/Marketing
• Strong technical leadership and decision-making skills; strong verbal and written communication skills to provide clear, crisp direction for key issue resolution; and good team skills to facilitate cross-functional cross -site team effectiveness.
Effect Of Board Clamping System On Solder Paste Print Quality Effect Of Board Clamping System On Solder Paste Print Quality Stencil printing technology has come a long way since the early 80s when SMT process gained importance in the electronics
Qinyi Electronics Co.,Ltd | https://www.qy-smt.com/shop/186854-boom-500mm-board-clamps-140570?page=37&category=1113
DEK BOOM 500MM BOARD CLAMPS 186854 | QYSMT × Home about Us ABOUT US FAQ SMT spare parts SMT surplus equipment SMT peripheral equipments News Contact US 0 0 Sign in contact us Products DEK BOOM 500MM BOARD CLAMPS Public Pricelist Public
KD Electronics Ltd. | http://www.kundasmt.com/a/PRODUCTS/3071.html
: Horizontal Hold Down Clamps 215-U Horizontal Hold Down Clamps 215-U PREVIOUS： 03025007-04 NEXT： 03025549-01 RELATED PRODUCTS CATEGORIES ABOUT US
