Industry Directory | Manufacturer
AIM is a leading global manufacturer of solder assembly materials for the electronics industry.
Specialty Solder Products for SMT Assembly- Solder Paste (No-Clean, Water Wash), Solder Spheres, Fluxes, Preforms, Wire, Ribbon.
New Equipment | Solder Materials
Indium Corporation manufactures high quality solder powders and pastes. Powders are available in hundreds of alloys and a full range of sizes. Solder pastes can be made from these powders using a wide variety of flux vehicles to get the best fit for
Electronics Forum | Wed Aug 10 07:55:21 EDT 2005 | ajaydoshi
we are using heareous F381, F352 no clean solder paste. specially in qfp for high frequency board we observe that cleaing / removing of ' no clean flux 'is require. if we do not clean same most of time after all test & envioumental test it shows pin
Electronics Forum | Wed Aug 10 08:10:39 EDT 2005 | davef
Comments are: * Sounds like it's necessary to clean "heareous F381, F352 no clean solder paste" in your application. Consider a paste that may be better suited to your application. * If you're cleaning "low residue flux", consider using an organic ac
Industry News | 2008-10-26 00:28:46.0
ROSEMONT, IL � Industry-leading associations IPC and SMTA jointly announce that Dave Adams (Session Chair) of Rockwell Collins, Lee Flasche of Delphi Electronics Group, Dr. Ning-Chen Lee of Indium Corporation, Steve Hugh of Philips Medical, and Dr. Ken Dishart formerly of DuPont will present in Session 4 on Lead-Free Cleaning. The symposium, jointly sponsored by IPC and SMTA, will be held at Crowne Plaza Chicago O'Hare in Rosemont, IL on October 28-29, 2008
Industry News | 2008-09-02 17:54:06.0
ROSEMONT, IL � Industry-leading associations IPC and SMTA jointly announce that Dale Lee of Plexus Corp., Doug Pauls of Rockwell Collins, Dr. Bill Kenyon of Global Centre Consulting, Dr. Ron Lasky of Indium/Dartmouth, and Lee Wilmot of TTM Technologies will be presenting during Session 1 on Industry Standards and Regulations. The symposium, jointly sponsored by IPC and SMTA, will be held at Crowne Plaza Chicago O'Hare in Rosemont, IL from October 28-29, 2008.
Technical Library | 2014-02-06 17:49:48.0
Many electronics manufacturers perform SIR testing to evaluate solder materials and sometimes the results they obtain differ significantly from those stated by the solder material provider. The difference in the results is typically the result of SIR coupon preparation. This paper will discuss the issue of SIR coupon preparation, board cleaning techniques, and how board cleanliness directly affects SIR results.
Technical Library | 2018-11-20 21:33:57.0
There are several industry-accepted methods for determining the reliability of flux residues after assembly. The recommended methods of test sample preparation do not always closely mimic the thermal cycle experienced by an assembly. Therefore, extraction from actual assemblies has become a popular method of process control to assess consistency of post-reflow cleanliness. Every method of post-reflow flux residue characterization will depend on the reflow process followed to prepare the coupon.This investigation will focus on the effect of thermal conditions on the remainder of active ingredients in flux residues after assembly with no-clean solder pastes.
Events Calendar | Wed Oct 20 00:00:00 EDT 2021 - Wed Oct 20 00:00:00 EDT 2021 | ,
Penang Chapter Virtual Vendor & Technical Day
Career Center | Houston, Texas USA | Engineering,Management,Quality Control,Technical Support
Seasoned Process & Quality Engineer. Degreed Chemical Engineer. 20+ years in Electronics Semiconductor manufacturing. Proficient in Quality Statistical tools, Design of Experiments, FMEAs, APQP, PPAP, ISO 9000, ISO/TS 16949 etc.
SMTnet Express, November 5, 2020, Subscribers: 28,030, Companies: 11,176, Users: 26,227 Higher Defluxing Temperature and Low Standoff Component Cleaning - A Connection? Credits: ZESTRON OEMs and CMs designing and building electronic
| https://pcbasupplies.com/leaded-solder-wire/
JM-20 Sn63/Pb40 – 1.6 mm No Clean Leaded Flux Cored Solder Wire Login Create Account Contact View My Cart Menu × Categories Hand Soldering
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/select/technologies-or-options/solder-nozzle-cleaning
printed circuit board eliminating contamination - Does not spray liquid or powdered flux, adipic or organic acid, and is advantageous for clean production shop floor environments - Produces no
