Industry Directory | Manufacturer / Other
Reduce electrical overstress (EOS) with our EMI filters for soldering, power, ground and servo motors. EMI filters improve equipment up-time and reliability and reduce test problems.
Industry Directory | Manufacturer / Other
solder pallets material ( alternative Durostone material, FR-4 laminated sheet ); solder pallets accessories(sold pallet hold down, clamps for solder pallets; PCB assembly tooling(wave solder pallet)
This anti-static work surface kit includes everything you need for ESD protection of micro-circuitry components. (1) 2' x 3' Anti-Static Bench Mat (1) Wrist Strap & 9' Coil Cord (1) 10" Common Point Ground
Ground EMI filter model GLE30-1 blocks high- frequency noise (EMI) on ground while providing while maintaining very low impedance for electrical safety. The filter is very easy to connect and it requires no maintenance. One of the most common appli
Electronics Forum | Wed Aug 23 08:55:39 EDT 2000 | Dave F
Dr. Lee: Taking a tangent on your response ... When talking about alternate solders. Bismuth forms an alloy with lead with a melting point of 93�C. Are there special conditions that cause this alloy to form? Or does the alloy form commonly when
Electronics Forum | Wed Aug 23 17:15:25 EDT 2000 | Dr. Ning-Cheng Lee
The ternary SnPbBi phase does form commonly when Pb and Bi are combined. No special condition required. Presence of this phase jeopardizes the reliability for applications involving temperature near 96C. Using low temperature solders means a lower s
Used SMT Equipment | In-Circuit Testers
The DET4TC2 and DET4TCR2 are designed for extended temperature range use with an IP54 rated enclosure making them genuinely outdoor instruments. The instrument provides all the functions required for ground system testing: variable frequency 2 pole,
Used SMT Equipment | In-Circuit Testers
Megger DET4TCR2 Ground ResistanceTester Megger DET4TCR2 Ground ResistanceTester Features: - Rechargeable earth system testers for four pole attached rod and stakeless techniques - 2 3 and 4 point testing at the turn of a switch - Attached
Industry News | 2003-06-09 09:16:38.0
The adoption of AWR EDA software supports REMEC�s continuous efforts to manage the substantial challenges of today�s wireless design technology.
Industry News | 2003-03-11 08:45:00.0
CAMtastic DXP is the latest version of Altium's complete CAM verification and editing system that bridges the gap between PCB design and manufacturing and facilitates communication between board designers, fabrication engineers, and their clients.
Parts & Supplies | Pick and Place/Feeders
Advantages of JUKI electric feeder With the electronic parts more sophisticated, more and more small, the use of electric feeder has become the standard placement of the placement machine, the old placement machine can use electric feeder has becom
Parts & Supplies | Pick and Place/Feeders
Smt Fuji NXT H01 nozzles 1.0 nozzle AA0AS00 used in pick and place machine Smt fuji nozzles models: FUJI NXT NOZZLE H01 PLACING HEAD Part Number Description AA0AS00 Nozzle 1.0 AA06800 Nozzle 1.3 AA0HL00 Nozzle 1.8 AA0HM00 Nozzle 2.5 AA0HN00
Technical Library | 2012-08-02 21:05:14.0
First published in the 2012 IPC APEX EXPO technical conference proceedings. Pure tin is a common finish for copper hook up wire, coaxial cable, ground braid and harness assemblies used on electronic assemblies. Historically there have been fewer reports o
Technical Library | 2016-02-04 19:11:47.0
In a typical mechatronic manufacturing functional test setup, actual load simulations are usually done by connecting the DUT outputs to power or ground in order to establish either a high or low side driver. Each output is connected with different load and the test will either be sequential or concurrent. At lower power levels, these can usually be managed with general purpose switches. However, when it comes to higher power levels of currents more than 5 amps, such switching and loading might pose a greater challenge. Furthermore, critically in the manufacturing line, the tradeoff between cost and test time would have a great influence on the test strategy.This paper will present some key points to design a cost effective high power switching and load management solution.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Cleanly and easily separate tab routed PCBs without dust. Singulating tab routed printed circuit cards in low to medium volume production quantities is safe and easy with the N100 Nibbler from FKN Systek. Blades are available in standard thicknesses
Training Courses | | | ESD Control Training Courses
Browse training and certification programs for electrostatic discharge (ESD) control in electronics assembly.
Training Courses | | | ESD Control Training Courses
Browse training and certification programs for electrostatic discharge (ESD) control in electronics assembly.
Events Calendar | Thu Aug 20 00:00:00 EDT 2020 - Thu Aug 20 00:00:00 EDT 2020 | ,
Avoiding the Most Common PCB Failure Modes
Events Calendar | Wed Oct 02 00:00:00 EDT 2019 - Wed Oct 02 00:00:00 EDT 2019 | ,
3D PCB Design and Analysis, When ECAD Meets MCAD
Career Center | Orange County, California USA | Quality Control
Job Description: Summary: Reporting to the COO/CTO the VP of Quality role will involve creating and/or augmenting the Quality system and programs to be a pro-active vs. a reactive structure. This will involve creating an overall quality vision, se
Career Center | Strongsville, Ohio USA | Accounting/Finance,Clerical,Engineering,Management,Production,Purchasing,Quality Control,Research and Development,Sales/Marketing,Technical Support
Spartronics is more than just a company. We have great facilities, a dedicated and talented team, tremendous capacity and capabilities, and longstanding customers who need us. Now, it’s all about driving forward with a winning strategy that bui
Career Center | Melbourne, Florida USA | Management,Production,Quality Control
Technical Skills/Abilities: � Management � Quality Assurance � Strong Troubleshooting Skills � Strategic Planning � Employee Training � Quality Assurance � Problem Resolution � Mechanical/Technical Aptitude
| https://unisoft-cim.com/place_make-point.html
. The MAKE POINT feature may be used for a number of reasons and a common one is when making an assembly program there may not be a clear fiducial mark to use as a reference point when creating the Pick
| https://www.eptac.com/blog/3-common-pcb-design-mistakes
3 Common PCB Design Mistakes Looking for solder training standards, manuals, kits, and more? Visit soldertraining.com Training Training Materials Locations Resources Ask Helena