Technical Library | 2019-05-17 01:50:39.0
Dry cabinet is especially designed with fully automatic humidity control to prevent moisture related defects. This cabinet is the optimal storage expert for SMT/BGA/PCB/IC electronic components.Our newly developed design greatly increases dehumidifying system which runs faster and more reliable compare to those traditional dry cabinets. it decreases the defective rate at production line.
Industry Directory | Manufacturer
Designer and manufacturer of custom electronic controllers. Focused on motor controls and appliance controls. RoHS and non-RoHS. SMD and Through Hole equipment. Conformal coating and light assembly.
Industry Directory | Manufacturer
Omni Controls is the best distributor for the high quality of test and measurement equipment supplies temperature and humidity equipment, analytical equipment, Dataloggers and Recorders etc. of reputed brand Megger, Extech, AEMC.
Technical Library | 2019-12-12 02:43:44.0
Today we discuss the reason that causes temperature humidity chamber to alarm,In most cases, the equipment alarm is caused by the improper operation in the process of use, which mainly includes following reasons:that are refrigeration system, temperature system and circulating system. First, Refrigeration system 1, refrigeration compressor overpressure alarm. If the refrigerant pressure exceeds the set value, it will stop and alarm at the same time. At this time, the fault must be eliminated and then manually reset. 2, short phase power supply, phase sequence alarm. When the external power supply of the equipment is out of phase or the phase sequence is changed, it will stop and alarm at the same time. 3. The circulating cooling water is short of water to alarm. When the water pressure of the cooling circulating water system is insufficient, it will stop and alarm at the same time, and it must wait for the fault to be eliminated and reset at the same time before it could run normally. 4, refrigeration compressor overheating alarm. When the coil of the compressor is overheated and the power supply of the line is not normal, it will stop and alarm at the same time. Second, Temperature system 1, the overtemperature alarm in the chamber. The sensors in the channel and the sample area are equipped with overtemperature protection devices, and there are also overtemperature protecter on the control panel. When the temperature in the working chamber exceeds the setting value on the controller, it will stop and alarm. 2. sample overtemperature protection. When the temperature in the sample area exceeds the protection temperature set by the controller, it will stop and alarm at the same time. The overtemperature protection of the sample is divided into upper limit protection and lower limit protection, which can be set according to the demand, Third,Circulating system 1. The alarm is caused by the overheating of the circulating fan. When the coil of the fan is over-heated, the alarm will be stopped at the same time. 2. The fan over-current alarm. When the current of the fan exceeds the allowable value, the alarm is stopped at the same time, and the normal operation can only be carried out after the fault maintenance of the overcurrent is completed. This is what we talk about today,if you have more questions,let us know.
Industry Directory | Manufacturer's Representative
World’s Largest Manufacturer of static shielding bags, moisture barrier bags, wrist straps and heel grounders. Our catalog features dry packaging, shielding bags, desiccant, vacuum sealers, humidity indicator cards, wrist straps, table and floor mats, heel grounders, meters, informational bulletins, and more. See our web site at www.scc-inc.com
Industry Directory | Manufacturer's Representative
World’s Largest Manufacturer of static shielding bags, moisture barrier bags, wrist straps and heel grounders. Our catalog features dry packaging, shielding bags, desiccant, vacuum sealers, humidity indicator cards, wrist straps, table and floor mats, heel grounders, meters, informational bulletins, and more. See our web site at www.scc-inc.com
Technical Library | 2019-11-17 22:46:45.0
Overview of walk-in temperature and humidity chamber: It also belongs to environmental test equipment, it tests whether the product can resist high temperature, low temperature, humidity, or the physical and chemical changes produced under extreme conditions, the walk-in temperature and humidity chamber volume is large, the product is placed, or a large object can be placed, such as automobile, new energy, television and liquid crystal screen, etc. How to do the routine maintenance of the walk-in temperature and humidity chamber: 1. The wet gauze basically, if there is no special case, s/b usually changed once in 3 months 2. The water channel shall be regularly cleaned, including water cup, water tank, etc., so as to prevent the water from being blocked,affect the humidity test. 3. It is forbidden to test the flammable and explosive products inside working room. 4. Clean the chamber on a regular basis 2. How to operate walk-in temperature and humidity chamber: The operation method is same as standard temperature humidity test chamber,the controller is 7-inch LCD programmable color screen, you only need to setthe temperature point---test time--how many cycles need to be tested, This can be done automatically, and the machine will stop automatically when it is complete. If there is any problem during the operation, the corresponding problem point will be displayed on the machine control screen. Walk-in temperature and humidity chamber is a must equipment for reliability test of Automobile,Aerospace,Electronic parts,etc,the operation and maintenance are easy,it is teh tear down mahcine,Climatest engineers will be dispatched to do on-site support,for instance,we will finish commissioning,train customers how to operate,maintain,welcome to follow our company facebook page:https://www.facebook.com/Climatechambers
Industry News | 2020-02-05 07:21:54.0
‘We have created a special room for the measurement & control systems customer who needs clean production environment for his very precise equipment. This dedicated room has strictly controlled levels of temperature, humidity and dust’ explains Przemysław Prolejko, Strategic Manager at Assel. ‘For every customer we build dedicated infrastructure should the customer have such a requirement’
Manufactures a wide range of environmental test solutions capable of temperature and humidity cycling, thermal shock, production stress screening, accelerated stress testing, combined environment testing, controlled humidity exposure.
Industry Directory | Distributor / Manufacturer / Other
Humidity Control equipment for factory static control
