Technical Library | 2018-05-17 11:14:52.0
Intermetallic compound (IMC) growth is being studied in earnest in this past decade because of its significant effect the solder joint reliability. It appears that from numerous investigations conducted, excessive growth of IMC could lead to solder joint failure. Leading to this, many attempts has been made to determine the actual IMC thickness. However, precise and true representation of the growth in the actual 3D phenomenon from 2D cross-section investigations has remained unclear. This paper will focus on the measuring the IMC thickness using 3D surface profilometer (Alicona Focus G4). Lead free solder, Sn3.0Ag0.5Cu (SAC305) was soldered onto copper printed circuit board (Cu PCB). The samples were then subjected to thermal cycle (TC) storage process with temperature range from 0 °C to 100 °C for 200 cycles and up to 1000 cycles were completed.
Technical Library | 2013-03-28 16:18:22.0
For the last couple of years, the main concerns regarding the electrical performance of blank PCB boards were impedance and ohmic resistance. Just recently, the need to reduce insertion loss came up in discussions with blank board customers (...) The paper describes the test vehicle and the testing methodology and discusses in detail the electrical performance characteristics. The influence of the independent variables on the performance characteristics is presented. Finally the thermal reliability of the boards built applying different copper foils and oxide replacements was investigated.
Industry News | 2008-01-31 00:10:18.0
GREELEY, CO � January 29, 2008 � FCT Solder, a division of FCT Assembly, and Nihon Superior USA, a subsidiary of Nihon Superior Co. Ltd., announce that it will exhibit SN100C� Lead-Free products paste in booth 213 at the upcoming IPC International Conference on Flexible Circuits, scheduled to take place February 12-14, 2008 in Phoenix, Ariz.
Industry News | 2012-09-06 18:12:36.0
Integral Technology has announced that PCB manufacturer TTM Technologies of Santa Ana, CA, will be the first factory certified to produce circuit boards using Integral's revolutionary Zeta® dielectric films.
Technical Library | 2018-01-17 22:47:02.0
Fine pitch copper (Cu) Pillar bump has been growing adoption in high performance and low-cost flip chip packages. Higher input/output (I/O) density and very fine pitch requirements are driving very small feature sizes such as small bump on a narrow pad or bond-on-lead (BOL) interconnection, while higher performance requirements are driving increased current densities, thus assembling such packages using a standard mass reflow (MR) process and maintaining its performance is a real and serious challenge. (...) In this study a comprehensive finding on the assembly challenges, package design, and reliability data will be published. Originally published in the SMTA International 2016
Technical Library | 2015-12-02 18:32:50.0
(Thermal Compression with Non-Conductive Paste Underfill) Method.The companies writing this paper have jointly developed Copper (Cu) Pillar micro-bump and TCNCP(Thermal Compression with Non-Conductive Paste) technology over the last two+ years. The Cu Pillar micro-bump and TCNCP is one of the platform technologies, which is essentially required for 2.5D/3D chip stacking as well as cost effective SFF (small form factor) package enablement.Although the baseline packaging process methodology for a normal pad pitch (i.e. inline 50μm) within smaller chip size (i.e. 100 mm2) has been established and are in use for HVM production, there are several challenges to be addressed for further development for commercialization of finer bump pitch with larger die (i.e. ≤50μm tri-tier bond pad with the die larger than 400mm2).This paper will address the key challenges of each field, such as the Cu trace design on a substrate for robust micro-joint reliability, TCNCP technology, and substrate technology (i.e. structure, surface finish). Technical recommendations based on the lessons learned from a series of process experimentation will be provided, as well. Finally, this technology has been used for the successful launching of the company FPGA products with SFF packaging technology.
Industry News | 2016-03-03 08:27:28.0
Nordson MARCH has recently released a white paper showing the results of RF plasma processing on conformal coating adhesion, the conformity of the coating coverage, and the resulting effects on electrical functionality of a fully assembled printed circuit board. The research was done in conjunction with Nordson ASYMTEK, AirBorn Electronics, and SMART Microsystems (formerly known as Desich SMART Center). The paper can be downloaded at http://bit.ly/MARCH-PlasmaWP.
Industry News | 2021-02-25 13:41:10.0
MacDermid Alpha Electronics Solutions, leaders in innovative electronic interconnect technologies, will feature their recent product releases and latest innovations, at the IPC APEX Virtual Conference and Expo, March 8-12, 2021.
Industry Directory | Consultant / Service Provider / Manufacturer
EMS company Laser SMT stencils mfg Tape converting , slitting , die cut Laser modules mfg Distribution materials,components ISO 9001:2015 ISO 13485:2016 AQAP 2110:2016 EN 9120:2018
Industry News | 2003-07-08 09:09:15.0
Available for Devices Up to 13 mm2 with Speeds Up to 1 GHz
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411