Industry Directory | Consultant / Service Provider / Distributor / Manufacturer
ORION provides innovative solutions to our customers' EMI/RFI Shielding, Insulating, Screening and Sealing needs in a broad spectrum of manufacturing environments.
Industry Directory | Manufacturer's Representative
Specialty materials for SMT Assembly. Solder Paste, Spheres, Tac Fluxes, Flip Chip Fluxes, Solder wi
New Equipment | Curing Equipment
A Pressure Cure Oven (PCO), or Autoclave, is used to minimize voiding and increase adhesion strength for bonding processes typically used in die attach and underfill applications. PCO pressurizes air into a rigid vessel and heats & cools with
The DV-7000 Heli-Flow® pump is a third-generation encoded auger pump. The pump has a floating head for use with footed needles to make fast, repeatable dots of solder paste and silver epoxy. The dispense gap is mechanically controlled by the needle,
Electronics Forum | Wed Apr 02 23:02:38 EST 2003 | scottf
I agree with Iman. Verify the integrity of the component for moisture. Most definately place an amount of ownership on your PCB supplier. Request tank analysis results and copies of the lot travelers. Look specifically for any in process rework pro
Electronics Forum | Tue Apr 01 11:50:08 EST 2003 | rdr
Dave, thanks for the info. This sounds like it would verify the presence of an open. We have verified that these balls are open and I am trying to figure out if we are fracturing or not wetting. causing these opens. I would use the die method on ne
Used SMT Equipment | Pick and Place/Feeders
Highlights of the SIPLACE CA: With the four SIPLACE SpeedStar heads for high-precision placements you can process up to 126,000 SMT components, 46,000 flip-chips, or 30,000 die-attach components per hour Component supplied from changeov
Used SMT Equipment | X-Ray Inspection
Very Nice Nicolet Xray Machine For Sale The system is complete and in good working condition See attached pictures and information below Nicolet Imaging Systems Model Number: NXR-1500 Serial Number: 0150011 Year 2000 Variable Speed Joystick
Industry News | 2009-02-02 18:48:47.0
Henkel today announced the appointment of Mr. Luc Godefroid as the company's Global Sales Director for its Semiconductor Group. A key member of Henkel's electronics sales team since 2001, Godefroid's new role sees him building on his previous success and directing the global sales efforts of Henkel's worldwide team and expanded product portfolio.
Industry News | 2011-11-20 13:36:13.0
GPD Global has been awarded two Global Technology Awards in the categories of Adhesives/Coatings/Encapsulants and Dispensing Equipment for its PCD Dispensing on the MAX Series Platform
Parts & Supplies | Pick and Place/Feeders
Cable: Control Die-Attach-Unit
Parts & Supplies | Pick and Place/Feeders
Transfer-X Motor Die Attach
Technical Library | 1999-08-27 09:24:56.0
Dispensing conductive adhesives in an automated factory environment creates some special challenges. A robust production process starts with understanding the adhesives in their fluid state and which important parameters must be controlled. Developing this understanding requires experience with a large number of materials and valves over time. Common uses of conductive adhesives in surface mount applications, die attach applications, and gasketing are addressed. As vendors of dispensing equipment, the authors see a constant stream of such applications. Dispensing requirements, techniques, and equipment resulting from this experience are discussed. Guidelines for optimizing quality and speed are given.
Technical Library | 2016-11-17 14:37:41.0
With increasing LED development and production, thermal issues are becoming more and more important for LED devices, particularly true for high power LED and also for other high power devices. In order to dissipate the heat from the device efficiently, Au80Sn20 alloy is being used in the industry now. However there are a few drawbacks for Au80Sn20 process: (1) higher soldering temperature, usually higher than 320°C; (2) low process yield; (3) too expensive. In order to overcome the shortcomings of Au80Sn20 process, YINCAE Advanced Materials, LLC has invented a new solderable adhesive – TM 230. Solderable adhesives are epoxy based silver adhesives. During the die attach reflow process, the solder material on silver can solder silver together, and die with pad together. After soldering, epoxy can encapsulate the soldered interface, so that the thermal conductivity can be as high as 58 W/mk. In comparison to Au80Sn20 reflow process, the solderable adhesive has the following advantages: (1) low process temperature – reflow peak temperature of 230°C; (2) high process yield – mass reflow process instead of thermal compression bonding process; (3) low cost ownership. In this paper we are going to present the die attach process of solderable adhesive and the reliability test. After 1000 h lighting of LED, it has been found that there is almost no decay in the light intensity by using solderable adhesive – TM 230.
General curing, die attach curing, underfill curing, film & tape bonding, wafer laminating.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Events Calendar | Wed Oct 23 00:00:00 EDT 2019 - Thu Oct 24 00:00:00 EDT 2019 | Guadalajara, Mexico
SMTA Mexico Expo 2019
Career Center | Boulder, Colorado USA | Engineering,Production,Quality Control
Senior-level micro-electronic technician capable of independent manufacture of custom hybrids, focal plane assemblies, and prototype detector assemblies in cleanroom environment (in Advanced Packaging and Detector Laboratory). MINIMUM QUALIFICATIONS
Career Center | South Plainfield, New Jersey USA | Management,Research and Development,Sales/Marketing
Alpha Assembly Solutions, a MacDermid Performance Solutions Business and a world leader in the development, manufacturing, and sales of innovative materials used in the assembly electronics, industrial joining and Photo Voltaic market places, is seek
Career Center | ORLANDO, Florida USA | Engineering,Maintenance,Production,Technical Support
Manufacturing tech/eng for a contract manufacture for 10+ years. Been working in the SMT industry for a total of 20yrs. Have done everything from operator to process work. Most familiar with Assembleon, MPM, DEK, BTU,Electrovert, SLIM-KIC, SUPER-MOLE
Career Center | SanPedro, Philippines | Maintenance,Production
Set-up Equipment machine and ensure its proper operation for costumer satisfaction. Carry out all Proactive Maintenance (PM) tasks such as predictive maintenance, preventative maintenance, failure finding maintenance and calibration maintenan
SMTnet Express, May 8, 2014, Subscribers: 22716, Members: Companies: 13872, Users: 36158 Challenges in Bare Die Mounting Larry Gilg, Die Products Consortium Bare die mounting on multi-device substrates has been in use in the microelectronics
GPD Global | https://www.gpd-global.com/co_website/loader-unloader-operations.php
Dispense Machine Side-Attach Loader, Unloader Home Products Fluid Dispensing Equipment High Precision Dispenser -MAX Series Large Format Board Dispensing -DS Series Table Top Dispensing Equipment Loader
ORION Industries | http://orionindustries.com/pdfs/200mp.pdf
# PCK Kiss cutting, steel rule 83# PCK Rotary die-cutting polyester (PET) and polycoated glassine (PCG) Selective die-cutting (cut adhesive before laminate
.gif)
.gif)
