Training Courses | | | IPC/WHMA-A-620 Trainer (CIT)
The Certified IPC/WHMA-A-620 Trainer (CIT) courses recognize individuals as qualified trainers in the area of cable and wire harness fabrication and installation, and prepares them to deliver Certified IPC/WHMA-A-620 Specialist (CIS) training.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Technical Library | 2019-05-30 11:02:07.0
In a previous Tech Tip (see Battery Selection for Electronic Systems), considerations were discussed for selecting an appropriate battery for an application. After selection, testing should be performed to confirm that the battery can provide the power required for the specific application. Some battery definitions should be understood when discussing power load qualification testing of batteries.
Technical Library | 2019-06-20 07:45:19.0
One of the two basic risks of employing the commercially accepted, Restriction of Hazardous Substances (RoHS) compliant, lead-free (Pb-free) electronics is the threat to the electronics reliability from the growth of tin whiskers. The other basic risk deals with Pb-free solder joint reliability.
New Equipment | Design Services
ACI's leading edge manufacturing technology and wide range of expertise with electronics technology offers a reliable solution to your engineering needs, including the development of new processes and materials for your packaging requirements. O
Technical Library | 2019-05-30 11:04:03.0
There exists a need to efficiently remove heat from power electronics within power systems to enhance performance. Thermal management is a critical function to that operation. Reducing the junction temperature of semiconductor power electronic devices enables them to operate at higher currents. Lowering operating temperatures reduces the thermal stress on electronic devices, which improves efficiency and reduces failures. To improve the heat removal process, the current heat transfer design of a power system has been analyzed and a variety of thermal interface materials (TIMs) and cold plate technologies have been evaluated. This paper will review some of these results.
Technical Library | 2019-05-31 14:15:01.0
ACI Technologies (ACI) is working on a project where one of the challenges is removing a large quantity of heat from audio amplifier circuits. This challenge is further complicated in that the heat generating circuits are located in a rack mounted box that needs to be shielded from electro-magnetic interference (EMI). Mechanically, this means that there cannot be open passages into the rack mounted box. We will first review the basic types of cooling available as commercial off-the-shelf (COTS) systems for the electronics industry, then discuss the pros and cons of each for different applications, and finally reveal the criteria and solution for the ACI project.
Technical Library | 2019-05-31 14:19:24.0
ACI Technologies (ACI) characterized the reliability of surface mount RF components. The RF frequency band of interest was the X band (10.7 to 11.7GHz). A two pronged test for reliability of circuit card assemblies (CCA) was designed for both extreme thermal cycling and vibration. The rapid thermal cycling and extreme vibration testing simulates the total stress encountered by the assembly over the life of the product but accomplishes it in a relatively short period of time. In order to perform the reliability testing, a test vehicle consisting of a printed circuit board with test structures and components, was designed, fabricated, and assembled at ACI.
Technical Library | 2019-06-03 15:32:40.0
ACI Technologies was pleased to assist a customer by conducting elemental analysis on several assemblies displaying severe corrosion. Several board assemblies had failed in the field and exhibited areas of corrosion in close proximity to onboard components. The most common source of corrosion on electronic assemblies is residual flux. Fluxes are specific chemistries applied during the soldering process which improve the wetting of the solder to both the pad and component when forming the solder joint. They can be highly reactive chemicals that, if left on the assemblies, can lead to corrosion, electrical degradation, and decreased reliability. In the presence of moisture and electrical bias, flux residue can enable dendritic growth as a result of electrochemical migration (ECM).
Technical Library | 2019-06-24 15:54:17.0
Defense systems and its manufacturers are often blamed for not embracing new and innovative technologies to manufacture products compared to its commercial counterparts. Commercial product manufacturers are known to think “outside the box” in coming up with new products which are cheaper, have fewer parts, and easier to manufacture using automation. Automation leads to consistent quality products which are reliable and reproducible. Implementing some of these producibility design practices into defense systems will greatly reduce the cost and insertion time for new products.
Reflow ovens for automated SMT PCB assembly, specializing in lead free processing and nitrogen reflow. The best convection reflow ovens on the market.
4 Vreeland Rd.
Florham Park, NJ USA
Phone: 973-377-6800
