Full Site - : fr5 vs fr4 (Page 2 of 5)

Re: FR4 vs Polymide

Electronics Forum | Fri May 15 18:13:35 EDT 1998 | Earl Moon

| | | Does the temp. profiles used to reflow double sided pcb's through a IR oven | | on FR4 board material have to be re-established if it is changed to | | polyimide? Boards will be baked out prior to assembly. | | any response would be most appr

CBGA vs PBGA

Electronics Forum | Wed Oct 25 10:33:08 EDT 2000 | Chris

I need to know the advantages or disavantages of a plastic or FR4/Flex based BGA over the ceramic based BGA. We have a BGA package we are going to have produced. Some want to have it made out of ceramic because they feel a ceramic package will be a

Re: FR4 vs Polyamide

Electronics Forum | Mon Feb 15 15:33:47 EST 1999 | Earl Moon

| Any info on the pros and cons of FR4 or Polyamide ref the use of soldering PGAs would be helpful. ie. temp co-efficient diffs, baking, wave soldering, Convection reflow etc | I'm sure you know all the basic differences as Tg, X, Y, and Z expansi

Re: CBGA vs PBGA

Electronics Forum | Wed Oct 25 12:24:02 EDT 2000 | Philip

Hi Chris! I hope this will help you! The CBGA uses an array of high melting point solder spheres(Sn10/Pb90) to connect its ceramic chip carrier to an epoxy glass (FR4) PCB using eutectic (Sn63/Pb37) solder joints at both ceramic and card inter

Re: FR4 vs Ceramic mismatch

Electronics Forum | Wed May 06 09:16:51 EDT 1998 | justin medernach

| I hear that there is a problem with using ceramic parts that are sizeable. Apparently, there is a mismatch in the Temperature Coefficient of Expansion between the FR4 and ceramic materials which causes the soldered erminations to weaken and eventua

Re: FR4 vs Ceramic mismatch

Electronics Forum | Fri May 15 09:07:12 EDT 1998 | Earl Moon

| | I hear that there is a problem with using ceramic parts that are sizeable. Apparently, there is a mismatch in the Temperature Coefficient of Expansion between the FR4 and ceramic materials which causes the soldered erminations to weaken and event

Mechanical Router vs Laser Depaneling

Electronics Forum | Tue Feb 06 04:54:39 EST 2018 | Robl

Smells a lot worse even with good extraction. Key things to look out for is laser life on your thickness and layup of panels compared to spindle motor life (Typically 10,000 hours, or 2 years for us) and cost of replacement lasers. We get spindle

cap size and copper thickness vs part size questions

Electronics Forum | Mon Nov 07 16:34:55 EST 2005 | CW

If I am putting chip capacitors on a .063 FR4 board, what size package should we stay away from to avoid cracking? If I use 2 mil copper on the outside layers of a PCB, am I limited to what pitch of parts I can use? Specifically, will using 0603

cap size and copper thickness vs part size questions

Electronics Forum | Mon Nov 07 16:31:47 EST 2005 | CW

hi Bob, Thanks for the info. I understand your comments, but I am looking for specific guidance, If I am putting chip capacitors on a .063 FR4 board, what size package should we stay away from to avoid cracking? (I realize this is dependent on h

Tg - Glass transition temperature

Electronics Forum | Thu Jan 20 16:06:38 EST 2000 | Mike Naddra

Regarding glass transition , does anyone have expierance glass wiht transition temperature specification , such as what are the detrimental effects of exceeding the Tg , how long over the glass transition temperature ,if any , is acceptable. Tg of di


fr5 vs fr4 searches for Companies, Equipment, Machines, Suppliers & Information