Full Site - : gsm stops (Page 8 of 12)

GSM1 Y Axis Limit Switch

Electronics Forum | Fri Apr 28 16:03:31 EDT 2017 | ilavu

I have GSM1 (OS/2) machine and it does not zero. The Y axis comes to all the way front to hard stop. I replaced the limit switch before the hard stop and can not find any way to test the signal from limit switch in diagnostic. I like to replace the c

GSM2 spindles Not seen for head

Electronics Forum | Tue Sep 29 09:39:02 EDT 2015 | rgduval

Hey, David, For service, check out 4TechUSA over in Detroit. It's not Chicago, but, you're closer to Detroit up there than I am down here in Houston :) For your issue....do you have access to the UIC Knowledge Base? The first issue I found in the

GSM1 occasional fault

Electronics Forum | Thu Feb 04 03:54:46 EST 2010 | mika

Hi, I know that I been out for this exact error message before (several years ago) and I am just thinking about it. It was something simple... Ok. When You say stops in the middle of placement phase; Do you mean in the first task block, have it alre

Backing up GSM - Segment Repair importance...

Electronics Forum | Fri Mar 18 08:50:21 EST 2005 | Bored

I usually delete segment repair files 'segrep' monthly without implications. It speeds the machine up when generating other segrep files. I believe it is just an archive for e-stop generated production files and has no bearing on management data. Hop

Backing up GSM - Segment Repair importance...

Electronics Forum | Mon Mar 21 21:38:40 EST 2005 | pmd

You do not need to back up segrep. This is only used for boards currently on the machine whenever the machine encounters a palm down or soft stop. It only contains what is mounted and or not mounted on that board. No System infomation is contained in

GSM2 Universal user name and password

Electronics Forum | Fri Oct 26 13:43:54 EDT 2012 | whispell

Make sure your machine configuration is correct. You may have something assigned to the machine that is no longer there. For 24V check to make sure all of the E-stop jumpers are plugged in.

GSM Zeroing problem

Electronics Forum | Thu Jul 09 15:17:48 EDT 2015 | goodting

Thanks for the inquiry. We used MCD (Motion Control Dia) tool to verify if that is caused by VRM board. No respond(I means the related axis was off) was detected. we swapped that board to other machine, the VRM card was good.... X axis was stopped, t

Universal GSM1 startup error

Electronics Forum | Wed Aug 12 12:02:41 EDT 2015 | edwaterfall01

I think the heart beat message comes up if the vision had not initialized. You have changed that already stop I think it is something else. Have you some money a Restore of the Machine Configuration and Mapping and Calibration Data?

GSM2 spindles Not seen for head

Electronics Forum | Tue Sep 29 18:20:56 EDT 2015 | ercdave1

Rob,. thank you very much for the reply. I will follow your recommendations and verify that the stop bar is not damaged or misaligned. I will also thank you for the info for the service . I will keep you posted. Thank you again. David

help GSM2 Spindles error: All spindles safe sensor not seen for head

Electronics Forum | Thu Mar 20 15:57:57 EDT 2014 | edwaterfall01

The numeric display number should be higher but only when all 7 spindles are moved down slightly from the full up position. The 7 spindles retract up to the Stop Bar. Each spindle assembly has a tapered hole thru it. This hole is in the block with t


gsm stops searches for Companies, Equipment, Machines, Suppliers & Information

SMT spare parts - Qinyi Electronics

Reflow Soldering 101 Training Course
Selective soldering solutions with Jade soldering machine

Wave Soldering 101 Training Course
Equipment Auction Automotive Electronics Supplier - Closure of Tier-One SMT Dvision: (10) ASM & Universal SMT Lines & Feeders Equipment as-new-as 2019! Dek | Koh Young | Speedline | Vitronics | Viscom

Best Reflow Oven
Pillarhouse USA for handload Selective Soldering Needs

Training online, at your facility, or at one of our worldwide training centers"
PCB Depanelizers

Low-cost, self-paced, online training on electronics manufacturing fundamentals