Electronics Forum | Sat Dec 17 16:46:45 EST 2011 | eadthem
Startup current depends on your configuration. ours dose zones 1,2/ 3,4/ 5/ 6,7 last i checked it pulled about 40-55 ish on start up and 25-35 during run. our profile is a slow ramp till 170c then a fast ramp to 285c 280c(last 2 zones). 1707's
Electronics Forum | Thu May 18 10:48:09 EDT 2006 | vikkaraja
Hi There, I used to have a similar problem with all of our new heller ovens. I converted them with fan blower controller kit. It is really easy to do or you can have done. Its about $900/oven. For now if you do not feel like investing any money , go
Electronics Forum | Sun May 20 23:15:34 EDT 2007 | dsd
George, The Radiator is only used on the older Nitrogen ready type Heller Ovens to attract the flux toward the Flux Filtration system. There should be two blowers in the Cooling zone where the radiator is to be fitted and there should be 4" ducting
Electronics Forum | Thu Jul 23 13:23:45 EDT 2020 | bmalhi
Small components blown issue could be due to one of the below. - Process issue; Make sure solder paste is fresh, if flux is drying out it will not hold parts properly. Check downward pressure of Pick Place. SOT may have to be pushed a little harder i
Electronics Forum | Tue Jan 31 17:18:37 EST 2017 | mainenetservices
You can contact Heller service by email info@hellerindustries.com to get help with any issue. High Deviation or high process alarm could be due to one of the below reason. A. Blower motor in subject zone is not running – check for air flow B. Heat
Electronics Forum | Wed Aug 14 13:39:59 EDT 2013 | eadthem
Most of this you have probably covered, but these are what have caused heating issues for us in our 1707 EXL. First, you would probably notice, but check that all blowers are turning by looking at there cooling fans in the top and bottom, Our 170
Electronics Forum | Thu Sep 16 12:06:29 EDT 1999 | Scott S. Snider
| | | Hi, | | | | | | Can someone pls suggest to me the best reflow temperature setting | | | for a force air convection oven. The details is as follow. | | | 1) Heller 1700s | | | 2) 12 zone---6 top and 6 bot | | | 3) Solder paste --- Qualitek 691
Electronics Forum | Tue Aug 13 10:09:10 EDT 2013 | dyoungquist
We have a Heller 1707EXL that we use for lead and lead-free production. It has both a mesh belt and edge rails. We run 90% of our assemblies on the mesh belt (leaving the edge rails wide open). I have noticed when profiling a board on the mesh bel
Electronics Forum | Wed Jun 22 13:00:12 EDT 2005 | slthomas
"His opinion was that you could never achieve 500cfm, even with a jet engine attached, as the outlet on the oven was too small..." I had that experience with a washer that blew steam out of the entrance. He said we'd collapse the pipe before we ever
Electronics Forum | Wed Oct 23 16:56:03 EDT 2002 | mikestringer
Hi Marc I too have been using a fully synthetic Motor oil on Heller reflow ovens for a number of years. In our case Mobil 1 5W-50. We have a field failure problem with some 1% resistors under conformal coating where sulphates are dissolving the si
Reflow ovens for automated SMT PCB assembly, specializing in lead free processing and nitrogen reflow. The best convection reflow ovens on the market.
4 Vreeland Rd.
Florham Park, NJ USA
Phone: 973-377-6800
