Electronics Forum | Tue Sep 18 07:52:29 EDT 2007 | davef
Does the change from supplier to supplier as a result of: * Board definition? * Differences in processing at fabs? 3 Specification Fir Tree General Technical Specification 3a Design/Layout: * IPC-2221 * IPC-2222 3b PCB Fab: * IPC-6011 * IPC-6012 * I
Electronics Forum | Tue May 29 20:22:19 EDT 2001 | davef
Well, no fault with your calculations from here. They appear to be correct. [Logic doesn't appear to be off to far off base, either. An epiphany, eh?] As mentioned in an earlier posting on this thread, consider following the recommendations of IP
Electronics Forum | Mon Aug 16 13:18:46 EDT 2004 | davef
You bet our reponse changes. Q2R: Hard gold thickness is 4 to 10 u" for Au and 300 to 400 u" for nickel A2R: This is a hard gold spec?? It looks like a ENIG spec. Although, the Ni is quite heavy, 150 uin is sufficient for most applications. The gol
Electronics Forum | Wed Jan 21 04:14:19 EST 2009 | sachu_70
Hi Adam, I would suggest you refer IPC-2221 guidelines which define plating thickness as: Nickel 2.5-5.0 um , Gold 0.08-0.23 um. Although ENIG is a standard process, there is an associated risk towards Gold embrittlement, Porous Gold, or Black pad de
Electronics Forum | Mon Feb 09 16:55:28 EST 2009 | cuperpeter
Hi Sachin, thanks for your feedback. According to our supplier, surface plating is electrolytic gold over Nickel(not ENIG), but I think that is a still improper thickness for Au. (according to 3rd Working Draft from September 2008 of IPC 2221B "0.4
Electronics Forum | Tue Nov 07 22:41:48 EST 2006 | davef
You are correct that hand soldering ceramic capacitors often causes them to crack. They do not take thermal shock well. You might be able to reduce the amount of cracking by following the rework repair guidelines discussed in the fine SMTnet Archiv
Electronics Forum | Wed Jun 26 09:10:21 EDT 2002 | davef
I want to suggest: * IPC-2221, Generic Standard On Printed Board Design * IPC-222X, Sectional Design Standard For Printed Board For Y Printed Boards ... but I just thumbed through both quickly and saw nothing, I really didn't spend as much time as I
Electronics Forum | Wed Mar 01 17:13:15 EST 2000 | Dave F
Sorin: Formulas for calculating heat dissipation of traces don�t seem to provide practical results. But there are some wonderful tables and graphs that will meet you needs. You may need to do some finagling when calculating vias and through holes,
Electronics Forum | Sat Nov 25 18:45:19 EST 2000 | Ashok Dhawan
I am getting black spots / stuff while I run gold finish PCB through reflow soldering process using NC solder paste.The affected spots have intermetalic as black in color. Does not solder very well. I did look at the archieve but could not find info
Electronics Forum | Tue Sep 26 15:48:32 EDT 2000 | Dave Hulbert
I'm a bit confused about reading IPC-275 (I know I should have IPC-2221/2222) but I'm sure they are similar. Anyway, I am doing a: Military, less than 100V, non-conformal coated PCB, External Etch Sec 5.3.1.4 Edge Spacing.. (Pg 61) says use Tabl
IPC is the trade association for the printed wiring board and electronics assembly industries.
Training Provider / Events Organizer / Association / Non-Profit
3000 Lakeside Drive, 309 S
Bannockburn, IL USA
Phone: 847-615-7100
.png)