New Equipment | Education/Training
Solder Training and Solder Certification Courses Taught in Accordance With IPC Soldering Guidelines. We offer a variety of customized courses set up specifically for our customers requirements. An example would be our combination type certificate t
New Equipment | Education/Training
This is a combination lectured and hands-on course covering the information in the IPC J-STD-001 document. The J-STD-001, “Requirements for Soldered Electrical & Electronic Assemblies”, describes materials, method and acceptance
Electronics Forum | Wed May 27 10:19:43 EDT 1998 | Jerry
We have no problems but orientation does matter. Orient with longest side of component body perpendicuar to wave. In other words the same preference as with through hole DIPS. Idea is the same as for through hole, that the surface tension will ten
Electronics Forum | Wed May 27 13:42:08 EDT 1998 | Chrys
| R&D is currently designing a board with smt components on both sides of the board. They are adding a 16 pin IC Gull wing. on the bottom side of the board. I have asked for only caps and resistors to be placed on the bottom side. Is there a recommen
Industry News | 2019-01-09 21:58:38.0
GPD Global will exhibit at IPC APEX EXPO 2019. Stop by Booth 2915 to see live demonstrations of machines and equipment. Experts will be there to discuss your production needs. Whether your project requires a pump for retrofitting or a fully automated dispense system, conformal coating, or component preparation, we have a solution for you.
Industry News | 2018-10-18 11:15:12.0
PCB Design and Layout Guidelines
Technical Library | 2020-05-07 03:46:27.0
The selective soldering process has evolved to become a standard production process within the electronics assembly industry, and now accommodates a wide variety of through-hole component formats in numerous applications. Most through-hole components can be easily soldered with the selective soldering process without difficulty, however some types of challenging components require additional attention to ensure optimum quality control is maintained. Several high thermal mass components can place demands on the selective soldering process, while the use of specialized solder fixtures and/or pallets often places an additional thermal demand on the preheating process. Fine-pitch through-hole components and connectors place a different set of demands on the selective soldering process and typically require special attention to lead projection and traverse speed to minimize bridging between adjacent pins. Dual in-line memory module (DIMM) connectors, compact peripheral component interface (cPCI) connectors, coax connectors and other high thermal mass components as well as fine-pitch microconnectors,can present challenges when soldered into backplanes or multilayer printed circuit board assemblies. Adding to this challenge, compact peripheral component interface connectors can present additional solderability issues due to their beryllium copper termination pins.
Technical Library | 2022-08-08 15:06:06.0
Selective soldering has evolved to become a standard production process within the electronics assembly industry, and now accommodates a wide variety of through-hole component formats in numerous applications. Most through-hole components can be easily soldered with the selective soldering process without difficulty however some types of challenging components require additional attention to ensure that optimum quality is maintained. Several high thermal mass components can place demands on the selective soldering process, while the use of specialized solder fixtures, or solder pallets, often places additional thermal demand on the preheating process. Fine-pitch through-hole components and connectors place a different set of demands on the selective soldering process and typically require special attention to lead projection and traverse speed to minimize bridging between adjacent pins. Dual in-line memory module (DIMM) connectors, compact peripheral component interface (cPCI) connectors, coax connectors and other high thermal mass components as well as fine-pitch microconnectors, can present challenges when soldered into backplanes or multilayer printed circuit board assemblies. Adding to this challenge, compact peripheral component interface connectors can present additional solderability issues because of their beryllium copper base metal pins. Key Terms: Selective soldering, drop-jet fluxing, sustained preheating, flux migration, adjacent clearance, lead-to-hole aspect ratio, lead projection, thermal reliefs, gold embrittlement, solderability testing.
Teresa Rowe, IPC director of assembly standards, highlights several revisions to IPC J-STD-001F, Requirements for Soldered Electrical and Electronic Assemblies and IPC-A-610F, Acceptability of Electronic Assemblies. The documents have been updated to
ALPHA® Preforms with solder paste adds solder volume.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | IPC-7711/7721 Specialist (CIS)
The Certified IPC-7711/7721 Specialist (CIS) training focuses on rework of electronic assemblies and repair and modification of printed boards and electronic assemblies.
SMT Express, Volume 2, Issue No. 3 - from SMTnet.com Volume 2, Issue No. 3 Thursday, March 16, 2000 Featured Article Return to Front Page Stencil Design for Mixed Technology Through-hole / SMT Placement and Reflow by William E. Coleman, Photo
| https://www.eptac.com/webinars/plated-through-hole-fill-understanding-the-process-and-assembly-requirements/
: Understanding the Process and Assembly Requirements Plated Through Hole Fill is always a hot topic of conversation and we continue to get questions about process issues and acceptable requirement
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/select/industries/automotive-and-transportation?con=t
Guadalajara Expo and Tech Forum Nordson SELECT Bob Klenke to discuss solutions for selective soldering of challenging through-hole components Nordson SELECT to Exhibit Award Winning Selective Soldering
