Industry Directory | Manufacturer
EBSO develops and manufactures cutting and bending machines for Thru Hole components and is a competent solution partner around Selective Soldering.
Industry Directory | Distributor / Manufacturer's Representative
Grip Technologies manufactures all forms of component processing equipment.
Form & Cut 2-, 3-, 4-, 5-, and 7-leaded Radial Components Capable of forming loose radial components at rates up to 5,000 parts per hour with a variable speed motor. Feed components by hand or with tubes (TO-220s) Reduce setup time with quick ch
New Equipment | Rework & Repair Equipment
Orange Sticks with double beveled ends, 7" x 5/32" (SH-83) The Beau Tech orange sticks are made of high quality non-resin wood which will not contaminate solder and component leads. Natural wood is among the best material that does not gen
Electronics Forum | Thu May 07 10:53:58 EDT 1998 | Ryan
Is there a machine for bending S shaped bends in leads of through-hole components, to keep them off the surface of the board.
Electronics Forum | Thu May 07 11:39:29 EDT 1998 | Dave F
| Is there a machine for bending S shaped bends in leads | of through-hole components, to keep them off the surface of the board. Ryan: Some lead forming equipment can form leads to stand-off the board. Some lead forming equipment suppliers are: Au
Used SMT Equipment | THT Equipment
ELECTROVERT/ELECTROPREP AUTOMATIC LEAD FORMING MACHINE MODEL 55000 PREPS AXIAL COMPONENTS AND RADIAL COMPONENTS. INCUDES 3 DIE SETS. A5340-000-04-4 0.4 INCH AXIAL A5340-000-02-5 0.5 INCH AXIAL A5470-000-20-0 TO220 HORIZONTAL
Used SMT Equipment | SMT Equipment
CM401-L Placement Machine B-type (MF) 2 Feeder Carts CE-Mark Transformer for 230/400 V 50 Hz 930 mm Pass line height 930 mm PCB Transfer Height (per Gang Cart) NG Components Ejection Conveyor Upstream Extension Conveyor Tray Lifter Shuttle (ST40S-20)
Industry News | 2017-01-26 19:53:00.0
GPD Global will exhibit in Booth 2933 at the upcoming IPC APEX EXPO 2017 scheduled to take place February14-16, San Diego Convention Center. GPD Global will officially launch its new, fully automated dispense platform, Hyperion, and a new, low cost conformal coating system.
Industry News | 2011-12-14 15:35:33.0
Manufacturing processes, handling and printed circuit assembly (PCA) test can put a lot of mechanical stresses on packages, causing failures. As grid array packages get larger, identifying how to set safe levels for these steps becomes more difficult. A new quantitative test methodology within IPC/JEDEC-9707, Spherical Bend Test Method for Characterization of Board Level Interconnects, lets users determine how much strain packages can take before reliability degradation.
Parts & Supplies | SMT Equipment
Manual Component Lead Cut Bend QY-306B Specifications Lead Forming Machine Lead Former is used to lead cutting and forming of taped, bulk resistors, diodes,and other axial components FEATHERS 1. This lead fomring mac
Parts & Supplies | SMT Equipment
Manual Component Lead Cut Bend QY-306B Specifications Lead Forming Machine Lead Former is used to lead cutting and forming of taped, bulk resistors, diodes,and other axial components FEATHERS 1. This lead fomring mac
Technical Library | 2022-09-25 20:18:33.0
Printed circuit board (PCB) bending and/or flexing is an unavoidable phenomenon that is known to exist and is easily encountered during electronic board assembly processes. PCB bending and/or flexing is the fundamental source of tensile stress induced on the electronic components on the board assembly. For more brittle components, like ceramic-based electronic components, micro-cracks can be induced, which can eventually lead to a fatal failure of the components. For this reason, many standards organizations throughout the world specify the methods under which electronic board assemblies must be tested to ensure their robustness, sometimes as a pre-condition to more rigorous environmental tests such as thermal cycling or thermal shock.
Technical Library | 2013-01-09 18:31:54.0
The increased temperatures associated with lead free processes have produced significant challenges for PWB laminates. Newly developed laminates have different curing processes, are commonly filled with ceramic particles or micro-clays and can have higher Tg values. These changes designed to reduce Z-axis expansion and improve the materials resistance to thermal excursions through primary attach and rework operations have also produced harder resin systems with reduced fracture toughness.
https://www.ascen.ltd/Products/Component_lead_forming_machine/ Motorized version ASCEN taped component axial lead forming machine AS-809F axial lead former, use for cut and bend axial components braid resistor,capacitor, inductor, diode and other ele
https://www.ascen.ltd/Products/Component_lead_forming_machine/ Motorized version ASCEN taped component axial lead forming machine AS-809F axial lead former, use for cut and bend axial components braid resistor,capacitor, inductor, diode and other ele
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Career Center | Tewksbury, Massachusetts USA | Production
Mycronic is a global high-tech company whose innovative solutions have been advancing electronics technology for over 40 years. Today we continue to grow and serve customers in an expanding variety of industries. What we do impacts the future of tech
Career Center | Brookfield, ALL USA | Management,Production
Training and Qualifications Mil standards 464 Mil Standards 2000 ESD Training Cellular Manufacturing TQM Totally Quality Manufacturing ISO 9000 and 9001 IPC Standards, IPCA-610 IPC-J-STD-001E OSHA training LEAN Manufacturing, JIT (Just In T
Career Center | , | 2011-11-16 09:17:11.0
Mil standards 464, Mil Standards 2000, ESD Training, Cellular Manufacturing, TQM Totally Quality Manufacturing, ISO 9000 and 9001 IPC Standards, IPCA-610, IPC-J-STD-001E, OSHA training, LEAN Manufacturing, JIT (Just In Time) Six Sigma, AS400 Systems
The Application of Spherical Bend Testing to Predict Safe Working Manufacturing Process Strains SMTnet Express January 9, 2013, Subscribers: 26086, Members: Companies: 9075, Users: 34138 The Application of Spherical Bend Testing to Predict Safe
Qinyi Electronics Co.,Ltd | https://www.qy-smt.com/shop/556-n-2530-bending-cutter127881304-214162?page=220&category=1111&order=name+desc
. ADD TO CART Inquiry Now > TDK Bending Cutter127881304 556-N-2530
GPD Global | https://www.gpd-global.com/pdf/lead-former/CF-8-Axial-Component-Former.pdf
. After the leads are crimped, the component advances to the bending station where the leads are held and formed by a roller mechanism that produces nick-free results
.gif)
