Industry Directory | Manufacturer
Expertise and equipment to support the most intricate and challenging wire bonding applications. Fine wire wedge bonders, heavy wire bonders, ribbon bonders for backend semiconductor assembly.
Industry Directory | Manufacturer
OEM Electronic Products and Equipment
A relay is an electrical control device that can give a specified amount of input and hold it long enough to make a predetermined change in the controlled amount in the electrical output circuit. When the input drops to a certain level and remains fo
Electronics Forum | Fri Mar 27 14:37:49 EDT 2009 | hcglitte
Has anyone any experience with pick and place machines from http://www.mechatronic-systems.com?
Electronics Forum | Thu Sep 20 07:51:59 EDT 2001 | darren jones
Hi All I am currently a maintence/process technician who is looking to forward his career into the engineering side of the industry. I will soon be starting a HNC mechatronics course (1 day a week) and wondered if any one knew of any sources of info
Used SMT Equipment | Tape and Reel
AH-280 Automated IC Programming Equipment follows the success of the mechatronic design of Leaptronix AH-480 Series and is greatly improved with an upgraded rotary robotic arm and two horizontal arms with four vertical axes equipped with specially de
Used SMT Equipment | Tape and Reel
AH-280 Automated IC Programming Equipment follows the success of the mechatronic design of Leaptronix AH-480 Series and is greatly improved with an upgraded rotary robotic arm and two horizontal arms with four vertical axes equipped with specially de
Industry News | 2023-07-31 19:27:39.0
The SMTA Workforce Development Program announces an open house on August 4, 2023 at Gogebic Community College in Ironwood, MI, USA. The event provides an opportunity for students and staff of the college to highlight their new Mechatronics program and how it addresses critical shortages in the U.S. electronics industry workforce.
Industry News | 2017-08-08 13:41:02.0
SMTA announces that Bill Bader, CEO of iNEMI, will keynote the 2017 Technical Innovations Symposium on Monday, September 18, 2017. The symposium is part of the SMTA International technical conference September 17 - 21, 2017 in Rosemont, Illinois. Bader’s presentation is titled “2017 iNEMI Roadmap Highlights Impacting Board Assembly over the Next 5-10 Years.”
Technical Library | 2016-02-04 19:11:47.0
In a typical mechatronic manufacturing functional test setup, actual load simulations are usually done by connecting the DUT outputs to power or ground in order to establish either a high or low side driver. Each output is connected with different load and the test will either be sequential or concurrent. At lower power levels, these can usually be managed with general purpose switches. However, when it comes to higher power levels of currents more than 5 amps, such switching and loading might pose a greater challenge. Furthermore, critically in the manufacturing line, the tradeoff between cost and test time would have a great influence on the test strategy.This paper will present some key points to design a cost effective high power switching and load management solution.
PicoScope 6000E Series oscilloscopes address complex waveform analysis challenges with up to 500 MHz bandwidth, 8 to 12 bits of vertical resolution and up to 4 gigasamples of deep capture memory. 21 serial protocol decoder / analyzers included as sta
Events Calendar | Wed Jul 19 00:00:00 EDT 2023 - Wed Jul 19 00:00:00 EDT 2023 | ,
SMTA Webinar: Secure, Intelligent, Detailed Design Data Exchange Between Design & Manufacturing
Career Center | San Jose, California USA | Engineering,Technical Support
Attention 2-4 year tech school/engineering graduates with a willingness to learn and travel! We are looking for a field service engineer based in Phoenix, LA or San Jose area that will be responsible for installing, servicing and training customers o
Career Center | Pitman, New Jersey USA | Engineering
Open Position: Field Service Engineer Company: Essemtec USA Location: Should be midwest, southeast, or west coast Job Description: Your tasks will include: • Installation, maintenance and repair of our equipment at customer site •
Career Center | , Honduras | Engineering,Maintenance,Management,Production,Quality Control,Technical Support
Several years working as a Mechatronic engineer in the field of automotive industry. I have worked on projects that included new product design and development, manufacturing processes, assembly lines, Continuous Improvement, quality improvement, fac
Career Center | KERALA, India | Engineering,Maintenance,Production,Technical Support
I have 2 year experience in SMT process
SMTnet Express, February 4, 2016, Subscribers: 24,087, Members: Companies: 14,964, Users: 39,872 Make the Right Design Choices in Load Switching and Simulation in a High Current and Mechatronic Functional Test Derek Ong, Lok Teng Kee, Chuah Rhun
Blackfox Training Institute, LLC | https://www.blackfox.com/4-industries-to-apply-hmp-solder-training/
. Surgical tools and instrumentation need to maintain their reliability under these conditions. 4. Automotive Like in the aviation industry, carmakers are now replacing mechanical and hydraulic systems with electromechanical or mechatronic systems, which consist of locating sensors, signal
