New Equipment | Rework & Repair Equipment
BGA Rework Stations from the BGA Experts with over 25 years rework process experience and customer support! For high volume BGA Rework on even the largest computer and networking boards! The model SV560A has a high resolution optical system for pla
New Equipment | Rework & Repair Equipment
RS-300Q set for SMD/BGA rework Integrated device: HOT-AIR station, quartz preheater and control computer 3 zone quartz preheater Preheater of A3 size Power of lower preheater: 3.4kW Power of upper preheater: 500W Smooth temperature adjustment
Electronics Forum | Mon Dec 31 09:00:06 EST 2001 | davef
Baking before assembly does nothing good. It: * Increases costs. * Adds steps to the process and makes scheduling more cumbersome. * Increases the amount corrosion on solderable surfaces. We used to bake to remove the moisture from boards that caus
Electronics Forum | Fri Aug 08 18:06:35 EDT 2003 | davef
Antistat sprays are a waste of time and money. These sprays just soaps disolved in water that absorb moisture from the air. Your minimum requirements: Conductive floor mats and wrist straps that are properly grounded. From there, consider using
Used SMT Equipment | Coating and Encapsulation
Asymtek C-740 Century Series Conformal Coating System The Century® C-740 Series Selective Conformal Coating system provides consistent, uniform dispensing of a variety of conformal coating materials for inline coating applications. The system v
Industry News | 2003-06-24 08:14:51.0
R/flex� 3850 laminate is produced in a range of copper and LCP thicknesses, just as the single-clad laminate, and is available in standard panel formats.
Industry News | 2020-07-22 04:45:00.0
MIRTEC is pleased to announce that Check Technology Solutions has purchased an MV-6 OMNI 3D AOI machine to meet their ongoing commitment to flawless manufacturing quality. The Award-Winning MV-6 OMNI is the perfect 3D Inspection Solution to enable Check Technology Solutions to achieve 100% customer satisfaction.
Technical Library | 2018-04-11 22:18:05.0
Millimeter-wave (mmWave) frequency applications are becoming more common. There are applications utilizing PCB technology at 60 GHz, 77 GHz and many other mmWave frequencies. When designing a PCB for mmWave frequency, the properties of the circuit materials need to be considered since they can be critical to the success of the application. Understanding the properties of circuit materials at these frequencies is very important.This paper will give an overview of which circuit material properties are important to mmWave frequency applications using PCBs. There will be data supplied which demonstrates why these properties are essential to the circuit material selection for mmWave applications. Some properties discussed will be dielectric constant (Dk) control, dissipation factor, moisture absorption, thickness control and TCDk (Temperature Coefficient of Dk). Measured comparisons will be shown for insertion loss and Dk versus frequency for different types of circuit materials up to 110 GHz. As part of the test data, the impact on circuit performance due to TCDk and moisture absorption will be shown at mmWave frequencies.
Technical Library | 2016-10-27 16:24:23.0
Press-fit technology is a proven and widely used and accepted interconnection method for joining electronics assemblies. Printed Circuit Board Assembly Systems and typical functional subassemblies are connected through press-fit connectors. The Press-Fit Compliant Pin is a proven interconnect termination to reliably provide electrical and mechanical connections from a Printed Circuit Board to an Electrical Connector. Electrical Connectors are then interconnected together providing board to board electrical and mechanical inter-connection. Press-Fit Compliant Pins are housed within Connectors and used on Backplanes, Mid-planes and Daughter Card Printed Circuit Board Assemblies. High reliability OEM (Original Equipment Manufacturer) computer designs continue to use press-fit connections to overcome challenges associated with soldering, rework, thermal cycles, installation and repair. This paper investigates the technical roadmap for press fit technology, putting special attention to main characteristics such, placement and insertion, inspection, repair, pin design trends, challenges and solutions. Critical process control parameters within an assembly manufacturing are highlighted.
The natural sustainable desiccant solution for moisture controlled packaging Desiccants are hygroscopic (moisture-adsorbent) substances that are packaged and used to protect a broad range of products from degradation due to moisture, helping to main
epoxy resin meter mix and dispensing machine for Current and Voltage Sensors Whatsapp +86 134 2516 4065 Model: PGB-200 PGB-200-800 system accurately meters, mixes and dispenses two-compon
Events Calendar | Tue Dec 11 00:00:00 EST 2018 - Tue Dec 11 00:00:00 EST 2018 | ,
Inspecting PWB Assemblies for Defects
Events Calendar | Wed Apr 21 00:00:00 EDT 2021 - Wed Apr 21 00:00:00 EDT 2021 | ,
Oregon Chapter Tutorial: How Clean is Clean and How Do You Know for Sure?
Career Center | Santa Cruz, California USA | Production,Quality Control
Soldering Technician, Touch-up for PCBAs Perform hand soldering and touch-up rework for Printed Circuit Board Assemblies (PCBA), cables and associated equipment. Inspect PCBA for defects, loose connections, missing components. Solder to perform r
| https://www.eptac.com/blog/3-strategies-for-effective-rework-repair-of-pcbs
3 Strategies for Effective Rework & Repair of PCB’s Looking for solder training standards, manuals, kits, and more? Visit soldertraining.com Training Training Materials Locations Resources Ask Helena
Imagineering, Inc. | https://www.pcbnet.com/blog/everything-you-need-to-know-about-moisture-sensitive-devices-msds/
. Additional Tips for Moisture Control Every re-bake resets the timer on how much moisture a device has absorbed. Take additional effort to record how often a printed circuit board is exposed to moisture