Industry Directory | Manufacturer's Representative
Specialty materials for SMT Assembly. Solder Paste, Spheres, Tac Fluxes, Flip Chip Fluxes, Solder wi
Industry Directory | Manufacturer
US manufacturer of metallized ceramic substrates & packages; specializing in PCTF (plated copper over thick film) & low cost AgENIG (silver with electroless nickel and immersion gold plating).
New Equipment | Fabrication Services
Base Material: FR4 Layer count: 4 layer Board thickness: 1.6mm Copper Thickness:1 oz Surface finish: nickel gold plating Soldermask Colors: Green Size:159.25*182/1up
At Barry: custom requests are common and welcome. We enjoy the challange. Extensive capabilities, wide material selection and state-of-the-art equiptment (including in-house plating and machining) ensure we can deliver a component fitting your exact
Electronics Forum | Mon Jan 29 12:42:24 EST 2001 | davef
Several points about your query are: * TI�s solderability protection specification is a minimum of 3 u" of palladium over 40-60 u" of nickel plate over a http://www.ti.com/sc/docs/products/logic/package/palladm/index.htm
Electronics Forum | Mon Jan 29 06:44:59 EST 2001 | Scott B
I have recently come across a device which has a palladium over nickel finish which when soldered shows evidence of poor wetting to the lead ( i.e. a wetting angle greater than 90�) about three quarters of the way up the side of lead. This is only vi
Industry News | 2003-05-19 10:06:43.0
The PCB is available with a maximum panel size of 406-by-460mm and a minimum board thickness of 0.8mm.
Industry News | 2003-04-09 08:25:50.0
A new design guide is available from Genalog detailing Samtec's flex circuit capabilities.
Parts & Supplies | Circuit Board Assembly Products
1) 160*100mm, FR-4 CTI ≥ 600V 2) 8 layer impedance control 3) Copper weight(finished inner/outer): 1 oz 4) LPI Green mask/white silk 5) Min hole 0.19mm, 5/3 track/gap 6) 1.6mm +/-10% thick 7) Immersiong gold over nickel
Parts & Supplies | Circuit Board Assembly Products
1). 1+C+1 HDI, buried/blind L1-L5/L5-L8 vias. 2). FR-4 Material, 1 oz weight. 3). 8 layer, 1.6mm thick. 4). 4/4 mils track and space 5). Min.drill 0.1mm 6). Green solder mask/ white silkscreen 7). Immersion gold over nickel
Technical Library | 2019-06-04 10:19:46.0
Interconnection technology relies very heavily on the ability of the conductors on a printed wiring assembly to maintain reliable signal integrity. Harsh environmental factors can precipitate a loss of conductivity due to oxidation and corrosion. Connections are typically soldered or inserted using pressure fitted connectors to obtain enough surface contact to meet the electrical conductivity requirements. In pressure contacts, surface integrity is especially critical where the abrasive effects of retraction and insertion can wear off the metallic finish from the contact area. This can expose the underlying copper or nickel and lead to increased resistance at the contact points. These types of conductors are frequently found in card edge connectors where the terminations are plated with a layer of nickel and gold (frequently referred to as gold fingers). A hard gold is typically used containing very small amounts of nickel and cobalt to increase the wear resistance.
Technical Library | 2019-06-07 14:49:54.0
ACI Technologies was contacted in regards to poor solder joint reliability. The customer submitted an assembly that was exhibiting intermittent opens at multiple locations on a ball grid array (BGA) component. The assembly’s functionality did not survive international shipping, essentially shock and vibration failures, immediately making the quality of the solder joints suspect. The customer was asked about the contract manufacturer and the reflow oven profile as well as the solder paste and surface finish used. The ACI engineering staff evaluated the contract manufacturer’s technique and determined that they were competent in the methods they used for placing thermocouples in the proper locations and developing the reflow oven profile. The surface finish was unusual, but not unheard of, in that it was hard gold over hard nickel, rather than electroless nickel immersion gold (ENIG). The customer was able to supply boundary scan testing data which showed a diagonal row of troublesome BGA pins.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
BEST Inc master instructor Norman Mier demonstrates how to replate gold fingers using the BEST gold contact replating kit. In this video he demonstrates how to repair, prepare and replate the finger using a gold replating solution. If you want to lea
Events Calendar | Wed Apr 20 00:00:00 EDT 2022 - Wed Apr 20 00:00:00 EDT 2022 | ,
Virtual Course: Selection Criteria of Surface Finish for Next Generation PCB Technologies
Events Calendar | Wed Mar 18 00:00:00 EDT 2020 - Wed Mar 18 00:00:00 EDT 2020 | College Park, Maryland USA
CALCE Reliability Science Symposium - Spring 2020
SMTnet Express, March 26, 2015, Subscribers: 22,542, Members: Companies: 14,271 , Users: 37,963 Effectiveness of Conformal Coat to Prevent Corrosion of Nickel-palladium-gold-finished Terminals Michael Osterman; Center for Advanced Life Cycle
Imagineering, Inc. | https://www.pcbnet.com/blog/everything-you-need-to-know-about-pcb-finish/
. Cost In the world of printed circuit boards, you get what you pay for. Generally, the more expensive PCB finishes like electrolytic wire bondable gold, electrolytic hard gold, and electroless nickel electroless palladium immersion gold (ENEPIG
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/march/about-us/events/smtai-2015
. RoHS mandated materials and advanced component characteristics can create challenges for conformal coating coverage and adhesion. Nickel-Palladium-Gold leads for instance can be difficult to deposit conformal coating on to, in particular the knees
