New Equipment | Solder Materials
We have a wide variety of flux-Cored solder, a mix of metal alloy, flux and other elements, that we have put together to match every type of application. This formula is designed so that the incidence of bridging is rare; likew
New Equipment | Solder Paste Stencils
EasyBraid’s stencil rolls are designed for use in SMT screen printing lines which keep stencil apertures clear of paste residues during the automatic screen printing process. They also clean the bottom of stencils, keeping them free from paste and fl
Electronics Forum | Wed Sep 15 01:16:36 EDT 2010 | dan_ems
Hello, what type of solder paste use, and this component is made for lead process?
Electronics Forum | Wed Sep 15 03:04:13 EDT 2010 | genesan
kester 562 clean process and this leaded part.
Industry News | 2003-04-04 08:46:37.0
Company Announces Further Reductions to Goodwill and Reclassifications of Indebtedness Recorded in Fiscal 2002
Industry News | 2014-01-29 10:18:33.0
The SMTA Capital Chapter is pleased to announce its first meeting of 2014 on March 4th, from 5:30 pm until 8 pm at Johns Hopkins Applied Physics Lab, 11100 Johns Hopkins Road, Laurel, MD 20723.
Technical Library | 2023-08-04 15:27:30.0
A designed experiment evaluated the influence of several variables on appearance and strength of Pb-free solder joints. Components, with leads finished with nickel-palladium-gold (NiPdAu), were used from Texas Instruments (TI) and two other integrated circuit suppliers. Pb-free solder paste used was tin-silver-copper (SnAgCu) alloy. Variables were printed wiring board (PWB) pad size/stencil aperture (the pad finish was consistent; electrolysis Ni/immersion Au), reflow atmosphere, reflow temperature, Pd thickness in the NiPdAu finish, and thermal aging. Height of solder wetting to component lead sides was measured for both ceramic plate and PWB soldering. A third response was solder joint strength; a "lead pull" test determined the maximum force needed to pull the component lead from the PWB. This paper presents a statistical analysis of the designed experiment. Reflow atmosphere and pad size/stencil aperture have the greatest contribution to the height of lead side wetting. Reflow temperature, palladium thickness, and preconditioning had very little impact on side-wetting height. For lead pull, variance in the data was relatively small and the factors tested had little impact.
Technical Library | 2016-12-22 16:44:04.0
Particulate matter contamination is known to become wet and therefore ionically conductive and corrosive if the humidity in the environment rises above the deliquescence relative humidity (DRH) of the particulate matter. In wet condition, particulate matter can electrically bridge closely spaced features on printed circuit boards (PCBs), leading to their electrical failure. (...) The objective of this paper is to develop and describe a practical, routine means of measuring the DRH of minute quantities of particulate matter (1 mg or less) found on PCBs.
https://www.ascen.ltd/Products/Automatic_SMT_equipment/PCB_conveyor/100.html PCB linking conveyor and PCB belt conveyor mainly used to connect different type PCB board handing equipment effectively for the SMT production line. ASCEN technology is ava
https://www.ascen.ltd/Products/Automatic_SMT_equipment/PCB_conveyor/100.html PCB linking conveyor and PCB belt conveyor mainly used to connect different type PCB board handing equipment effectively for the SMT production line. ASCEN technology is ava
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/lead-width-on-axial-through-hole_topic875.html
: DIOAD800W52L600D150B Diodes, Non Polarized Axial Diameter; Lead Spacing 8.00; Lead Width 0.52; Body Length 6.00; Body Diameter 1.50 And on page 3: W = Maximum Lead Width
| https://pcbasupplies.com/s3x58-m500c-7-500-gm/
– 500 gm Type-4 No-Clean Powerful Wetting Lead-Free SAC305 Solder Paste Good and Consistent Wetting Spreading to Oxidized Metal Surface
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
.gif)
