Industry Directory | Manufacturer
Maximart has 27-year-experience of manufacturing vertical machining center, EDM machine, precision lathe, 5 axes machining center and milling machine. Please take time to visit our website.
Technical Library | 1999-05-06 11:42:16.0
The most reliable and well-designed electronic device can malfunction or fail if it overheats. Considering thermal issues early in the design process results in a thermally conscious system layout and minimizes costs through the use of passive cooling and off-the-shelf components. When thermal issues are left until completion of the design, the only remaining solution may be a costly custom heat sink that requires all the space available. Incorporating a heat sink or a fan into a product after it is fully developed can be expensive, and still may not provide sufficient cooling of the device.
Technical Library | 2022-09-29 14:08:42.0
Electronic vehicles, devices and components must not overheat, otherwise they may fail to operate correctly. Thermal management is a major technical challenge as components are getting smaller, power densities are increasing and demands on robustness and reliability are becoming more stringent. To prevent power losses or defects resulting from overheating, liquid thermal interface materials (TIMs) are being increasingly used to dissipate their heat. This White Paper discusses the aspects that need to be taken into account when dispensing these mostly highly viscous, highly abrasive materials and why in many cases they are better alternatives to pads, tapes and foils.
Hot Bar Soldering/Bonding Machine
Parts & Supplies | Soldering - Wave
Overseas Agent and Distributor Wanted ! Features : Spray Fiuxer: 1) Oriental motor drives the flux spraying system. Spraying speed is adjusted according to PCB board width and moving speed to ensure even spraying all time. 2) Durable “Meiji
Versatile reflow oven for medium volume soldering (leadfree or leaded solder). 400 mm process width. Integrated microprocessor for profile control and storage. Extra high air volume for perfect soldering of complex boards. 5 zone reflow oven 400
New Equipment | Test Equipment
Kingsine K3063 USD $32,000.00 10 output channels Protection Relay Test Set K3063 8-channel output: 3x30A /4x 130V/Aux. DC High power:3X450VA at 30A (current generator). 4 x 60VA at 0 ... 130 V (voltage generator) High Prec
Industry News | 2021-08-12 20:58:16.0
When we use the Refrigeration Compressors, there could be frosting. It's a failure that we can solve. So this article will take you to look at the reasons for frosting and the corresponding solutions.
Technical Library | 2019-05-21 00:21:26.0
Continue to talk about the dust removal from temperature humidity test chamber. Cleaning and maintenance: 1) Pls remove internal impurities inisde chamber before operation. 2) The power distribution room should be cleaned at least once a year, and the dust can be removed by vacuum cleaner. 3) The exterior chamber must also be cleaned more than once a year, which can be wiped with soapy water. Inspection and maintenance of humidifier: The water storage in humidifier should be replaced once a month to ensure clean water quality, humidifying water tray should be cleaned once a month to ensure smooth flow of water. The inspection of over-temperature protector:during the test: If the temperature is over 20 ℃ ~ 30 ℃ than the maximum value setted,the power supply of the heater will stop, the "OVERHEAT" overt-emperature warning light will automatically turn on but the fan is still in operation, if the equipment runs without operator around,the operator should check the over-temperature protector in advance to ensure wether it has been setted properly before start [wet ball over-temperature protector set to 120 ℃].
Industry News | 2021-08-29 21:11:45.0
A compressor is a kind of driven fluid machinery that elevates low-pressure gas to high pressure. It is the heart of the refrigeration system. It inhales refrigerant gas with low temperature and low pressure from the suction pipe, compresses the piston driven by the motor, and then emits refrigerant gas with high temperature and high pressure to the exhaust pipe to provide power for the refrigeration cycle.
