Industry Directory | Manufacturer
A manufacturer of desoldering braid (wick) with an emphasis on continuing advancement in soldering/desoldering technology, visual and x-ray inspection systems, fume extraction, and solder paste inspection systems.
New Equipment | Solder Materials
Tip tinner to aid in cleaning and re-tinning solder iron tips de-wetted by use which can’t be repaired with sponge pads and cored solder wire. Use of TTC100C LEAD FREE Tip Tinner offers the following advantages: Lead Free SN100C tin/copper/nic
New Equipment | Rework & Repair Equipment
Desoldering braid (wick) is copper braid used in the rework and repair of printed circuit boards, computers, cell phones, or other electronics. Electronic components are often mounted on a circuit board and careful desoldering of components results i
Electronics Forum | Wed May 07 01:50:03 EDT 2008 | andrzej
We have received in one lot PCBs with defect of not wetting properly. Pads were finished with HASL but they were matte rather then shiny (attachment). For me looks like they are oxidized. Interesting is there was just top side with such defect. We h
Electronics Forum | Thu Jun 29 04:50:42 EDT 2023 | SMTA-70263692
This looks like it could be related to oxidation.Do you per-bake your pcb before assembly to remove any moisture inside your board panel?
Industry News | 2022-11-11 07:33:41.0
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board pads.
Industry News | 2022-10-13 07:44:15.0
I.C.T SMT Vacuum Reflow Oven Machine helps you to solve the problem of High Solder Voids Rates
Technical Library | 2020-10-14 14:33:36.0
Epoxy based adhesives are prevalent interface materials for all levels of electronic packaging. One reason for their widespread success is their ability to accept fillers. Fillers allow the adhesive formulator to tailor the electrical and thermal properties of a given epoxy. Silver flake allow the adhesive to be both electrically conductive and thermally conductive. For potting applications, heat sinking, and general encapsulation where high electrical isolation is required, aluminum oxide has been the filler of choice. Today, advanced Boron Nitride filled epoxies challenge alternative thermal interface materials like silicones, greases, tapes, or pads. The paper discusses key attributes for designing and formulating advanced thermally conductive epoxies. Comparisons to other common fillers used in packaging are made. The filler size, shape and distribution, as well as concentration in the resin, will determine the adhesive viscosity and rheology. Correlation's between Thermal Resistance calculations and adhesive viscosity are made. Examples are shown that determination of thermal conductivity values in "bulk" form, do not translate into actual package thermal resistance. Four commercially available thermally conductive adhesives were obtained for the study. Adhesives were screened by shear strength measurements, Thermal Cycling ( -55 °C to 125 °C ) Resistance, and damp heat ( 85 °C / 85 %RH ) resistance. The results indicate that low modulus Boron Nitride filled epoxies are superior in formulation and design. Careful selection of stress relief agents, filler morphology, and concentration levels are critical choices the skilled formulator must make. The advantages and limitations of each are discussed and demonstrated.
link: https://www.ascen.ltd/Products/Automatic_SMT_equipment/PCB_loader/87.html The automatic PCB magazine loader is used at the starting of the SMT production line for loading of PCBA to the line.he unit loads the production line automatically by pu
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Career Center | NORTHRIDGE, California USA | Engineering
EDUCATION BS Electronics and Communication Engineering Gujarat University MS Electrical Engineering California State University, Northridge ACADAMIC PROJECT Fabrication and Characterization of Silicon Carbide (SiC) MESFE
| http://etasmt.com/cc?ID=te_news_industry,24564&url=_print
. Dewetting directly impacts the quality of solder joints. Root Cause Analysis The PCB pads or the component‘s pins are oxidized. An oxidation layer prevents contact between the solder and the surface plating layer
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/pcb-design-in-the-1970s_topic2333.html
. We manually sketched the pads and traces with red and blue pencils on vellum parchment paper using a 10 th inch grid pattern on a drafting table using a T-square and triangle and circle templates