Parts & Supplies | SMT Equipment
KH4-M655F-20X YAMAHA YV100X YV100II SENSOR nozzle KM0-M711C-02X KM0-M711D-00X KM0-M711E-00X KG7-M71AB-A0X KG2-M7191-100 KG2-M7191-200 KG2-M7191-300 KG2-M7191-400 KG2-M7191-500 K38-M7113-H00 K38-M7113-B03 K38-M7113-C00 K38-M7113-D
Parts & Supplies | SMT Equipment
JUKI KE750-760.2010 VACCUM SENSOR nozzle KM0-M711C-02X KM0-M711D-00X KM0-M711E-00X KG7-M71AB-A0X KG2-M7191-100 KG2-M7191-200 KG2-M7191-300 KG2-M7191-400 KG2-M7191-500 K38-M7113-H00 K38-M7113-B03 K38-M7113-C00 K38-M7113-D01 K38-M
Parts & Supplies | SMD Placement Machines
PANASERT / UNIVERSAL / DYNAPERT PARTS FOR SALE N434UQ04041 Tube BLKE01252 FUSE 5A 40833025 FUSE 1.5A 42453904 FUSE 5A 42453907 FUSE 1A 46347803 Relay 40525301 SHOCK ABSORBER KXF0DSSAA00 46849802 SENSOR 46347803 RELAY 47323702 PROX SWITCH PNP N
Parts & Supplies | SMD Placement Machines
PANASERT / UNIVERSAL / DYNAPERT PARTS FOR SALE N434UQ04041 Tube BLKE01252 FUSE 5A 40833025 FUSE 1.5A 42453904 FUSE 5A 42453907 FUSE 1A 46347803 Relay 40525301 SHOCK ABSORBER KXF0DSSAA00 46849802 SENSOR 46347803 RELAY 47323702 PROX SWITCH PNP N
Electronics Forum | Mon Mar 25 08:45:24 EST 2002 | davef
Not dumb at all. It's a 16 pin, 0.65mm plastic SMT package with pads along the package edges proprietary to Fujitsu. Look here: http://www.fme.fujitsu.com/products/pll/pdf/bccover.pdf
Electronics Forum | Tue Mar 21 21:03:55 EST 2006 | davef
1 Chatter about mask opening � No BIG problems with these statements. It�s just that you may need to tailor your reflow recipe to minimize these escapees. 2 Stencil design - Any area ratio below 0.66 is going to very challenging to print, as you ca
Electronics Forum | Sat Mar 18 02:21:31 EST 2006 | pavel_murtishev
Good morning, Once again a met annoying solder beading issue while producing board with PLL (leadless, contacts from the bottom side of the package). Board has very high placement density and beads appear near PLL package only. This package is finep
Electronics Forum | Tue Mar 21 02:15:26 EST 2006 | pavel_murtishev
Good morning Dave, Here are some of my assumptions. Please correct me if I am wrong. 1. Mask opening. Due to mask to PCB misregistration mask is not always centered relative to pad center how is should be. Sometimes edge of the mask matches with ed
Electronics Forum | Mon Mar 20 22:39:03 EST 2006 | davef
Pavel Point: You suspect that solder paste can easily get to solder mask causing beading, because the aperture is larger than the component pad. Comment: Probably, this is incorrect. We overprint on solder mask all day long when doing paste-in-hol
.png)
