Industry News | 2009-09-17 14:28:17.0
NASHVILLE — September 2009 — Kyzen, a world leading provider of environmentally responsible precision cleaning products for electronics and high-technology manufacturing operations, announces that Mike Bixenman, CTO, along with co-author Mike Konrad, President of Aqueous Technologies, will hold a presentation titled “Cleaning for Reliability Post QFN Rework” at the upcoming SMTA International conference, scheduled to take place October 6-7, 2009 at The Town and Country Resort and Convention Center in San Diego.
Industry News | 2010-05-29 18:57:32.0
MARTIN will demonstrate the Reball/Prebump 03.1 unit at the upcoming SMTA Upper Midwest Expo, scheduled to take place Wednesday, June 9, 2010, at the Sheraton Bloomington Hotel in Bloomington, MN. This standalone unit is an easy and cost effective solution for BGA reballing and QFN solder bumping.
Industry News | 2010-06-30 12:09:49.0
MARTIN will demonstrate the Reball / Prebump 03.1 unit at the upcoming SMTA Ohio Valley Expo & Tech Forum, scheduled for Wednesday, July 14, 2010 at the Doubletree Hotel in Cleveland, OH. This standalone unit is an easy and cost effective solution for BGA reballing and QFN solder bumping.
Technical Library | 2021-08-25 16:28:36.0
In this study, a Sn–Bi composite solder paste with thermosetting epoxy (TSEP Sn–Bi) was prepared by mixing Sn–Bi solder powder, flux, and epoxy system. The melting characteristics of the Sn–Bi solder alloy and the curing reaction of the epoxy system were measured by differential scanning calorimeter (DSC). A reflow profile was optimized based on the Sn–Bi reflow profile, and the Organic Solderability Preservative (OSP) Cu pad mounted 0603 chip resistor was chosen to reflow soldering and to prepare samples of the corresponding joint. The high temperature and humidity reliability of the solder joints at 85 #14;C/85% RH (Relative Humidity) for 1000 h and the thermal cycle reliability of the solder joints from
Sn96.5Ag3.0Cu0.5 no-clean Solder Paste NP560 lead-free soldering paste SMT Solder Paste Sn96.5Ag3.0Cu0.5 no-clean Solder Paste NP560 flux solder paste Product description: Sn96.5Ag3.0Cu0.5 no-clean Solder Paste NP560 is a no-clean, lead-free,
"The IR 3000 offers advanced surface mount rework capability in an integrated, cost-effective, bench-top work station." This video covers the basic processes of the IR 3000, focusing primarily on: Installations, Removals, Component Alignment and Ins
Technical Library | 2009-11-05 11:17:32.0
Head-in-pillow (HiP), also known as ball-and-socket, is a solder joint defect where the solder paste deposit wets the pad, but does not fully wet the ball. This results in a solder joint with enough of a connection to have electrical integrity, but lacking sufficient mechanical strength. Due to the lack of solder joint strength, these components may fail with very little mechanical or thermal stress. This potentially costly defect is not usually detected in functional testing, and only shows up as a failure in the field after the assembly has been exposed to some physical or thermal stress.
Technical Library | 2016-02-11 18:26:43.0
Although reflow ovens may not have been dramatically changed during the last decade the reflow process changes step by step. With the introduction of lead-free soldering not only operation temperatures increased, but also the chemistry of the solder paste was modified to meet the higher thermal requirements. Miniaturization is a second factor that impacts the reflow process. The density on the assembly is increasing where solder paste deposit volumes decreases due to smaller pad and component dimensions. Pick and place machines can handle more components and to meet this high through put some SMD lines are equipped with dual lane conveyors, doubling solder paste consumption. With the introduction of pin in paste to solder through hole components contamination of the oven increased due to dripping of the paste.
Industry News | 2009-03-18 17:08:59.0
FINETECH will demonstrate today's most requested advanced rework applications in booth #2059 at the upcoming APEX 2009, scheduled to take place March 31 � April 2, 2009 at the Mandalay Bay Convention Center in Las Vegas.
