In-Line X-ray Inspection System Automatically in-line inspect Solder joint defects of PCBA and other defects on Hidden Components. Able to judge Good/NG fast with inspection speed of 1sec/FOV and the program can set ROIs conveniently. Performing X-r
New Equipment | Solder Materials
AIM introduces M8 Solder Paste, a high reliability no clean paste for use with SAC305, REL22, REL61, and Sn/Pb alloys. M8 no clean solder paste is designed for the most demanding high density electronic assemblies. An evolution of the highly success
Electronics Forum | Mon Aug 14 14:53:51 EDT 2017 | emeto
AIM, Indium , Alpha will be your top 3 choices. I did paste evaluation before with 4 paste manufacturers and Kester was my choice number 4. Profile according to the paste specs and observe results.
Electronics Forum | Thu Aug 10 07:29:43 EDT 2017 | stivais
How do you evaluate the soldering quality for those QFNs? X-Ray or AOI? For some QFNs (and other bottom termination components) it's not supposed to have solder fillets on toes. It's also noted in IPC-A-610 (Rev.F 8.3.13). Take a look at your QFN ch
Industry News | 2013-09-10 12:18:26.0
The Surface Mount Technology Association (SMTA)'s Intermountain Chapter will hold its annual technical symposium on September 19 at the University of Utah in the Warnock Engineering Building, Salt Lake City, Utah.
Industry News | 2014-06-17 21:50:29.0
SMT International has just introduced AMTECH VS-213 (a.k.a. the VOIDSTOPPER), a no-clean, lead-free solder paste formula that is 100% halogen-free based on all testing methods, including Oxygen Bomb Combustion and Ion Chromatography.
Technical Library | 2020-11-24 23:01:04.0
The miniaturization trend is driving industry to adopting low standoff components or components in cavity. The cost reduction pressure is pushing telecommunication industry to combine assembly of components and electromagnetic shield in one single reflow process. As a result, the flux outgassing/drying is getting very difficult for devices due to poor venting channel. This resulted in insufficiently dried/burnt-off flux residue. For a properly formulated flux, the remaining flux activity posed no issue in a dried flux residue for no-clean process. However, when venting channel is blocked, not only solvents remain, but also activators could not be burnt off. The presence of solvents allows mobility of active ingredients and the associated corrosion, thus poses a major threat to the reliability. In this work, a new halogen-free no-clean SnAgCu solder paste, 33-76-1, has been developed. This solder paste exhibited SIR value above the IPC spec 100 MΩ without any dendrite formation, even with a wet flux residue on the comb pattern. The wet flux residue was caused by covering the comb pattern with 10 mm × 10 mm glass slide during reflow and SIR testing in order to mimic the poorly vented low standoff components. The paste 33-76-1 also showed very good SMT assembly performance, including voiding of QFN and HIP resistance. The wetting ability of paste 33-76-1 was very good under nitrogen. For air reflow, 33-76-1 still matched paste C which is widely accepted by industry for air reflow process. The above good performance on both non-corrosivity with wet flux residue and robust SMT process can only be accomplished through a breakthrough in flux technology.
Technical Library | 2018-05-23 12:12:43.0
Driven by miniaturization, cost reduction and tighter requirements for electrical and thermal performance, the use of lead-frame based bottom-termination components (LF-BTC) as small-outline no-leads (SON), quad-flat no leads (QFN) packages etc., is increasing. However, a major distractor for the use of such packages in high-reliability applications has been the lack of a visible solder (toe) fillet on the edge surface of the pins: because the post-package assembly singulation process typically leaves bare copper leadframe at the singulation edge, which is not protected against oxidation and thus does not easily solder-wet, a solder fillet (toe fillet) does not generally develop.
#Xray#Inspection#SEC Nano-focus Tube of 200 nano resolution which is specialized for sub-micron defects of Semiconductor Packaging, Wafer Level Packaging(WLP). -Non-destructive Analysis System -High-Resolution Image with Dual Type CTs -Application
![[SEC] 3D In-line AXI Solution X-eye 6300 X-ray Inspection Machine](https://img.youtube.com/vi/w-_v-XDRKro/sddefault.jpg)
3D In-line Automated X-ray Inspection system (machine) Model: X-eye 6300 X-ray Tube: 160kV / 500 µa Table Size: Max. 330 x 250mm Min. 50 x 50mm Detector: 12 inch FPXD Defection type (Application): BGA, PoP, chip, QFN, QFP, etc. - High-speed In-lin
Career Center | Wesley Chapel, Florida USA | Engineering,Management,Quality Control
15 years of experience on Electronic Manufacturing. Certified SMT Process Engineer TQM Knowledge Statistics DOE Screen Printer Thermal Process Knowledge JIT International Project Engineering Experience
Modern 2D / 3D X-Ray Inspection - Emphasis on BGA, QFN, 3D Packages, and Counterfeit Components Modern 2D / 3D X-Ray Inspection - Emphasis on BGA, QFN, 3D Packages, and Counterfeit Components With PCB complexity and density increasing and also
