Industry News | 2010-06-04 17:36:28.0
DENVER — Krayden, Inc., a leading distributor of engineered materials, introduces the Permabond TA459 magnet adhesive that is non-corrosive to electrically conductive surfaces including copper.
Industry News | 2009-03-01 22:13:07.0
OSAKA, JAPAN � February 2009 � Nihon Superior Co. Ltd., a supplier of advanced soldering and brazing materials to the global market, announces Extra Fine Solder Wire SN100C (030) provides sharp spreading and good separation.
Industry News | 2021-12-15 20:08:31.0
Siemens pressure transmitter is a kind of equipment which converts pressure into pneumatic signal or electric signal for control and remote transmission. It can convert the physical pressure parameters such as gas and liquid sensed by the load cell sensor into standard electrical signals (such as 4 ~ 20mADC), which can be supplied to the secondary instruments such as indicating alarm instrument, recorder and regulator for measurement, indication and process adjustment.
Industry News | 2010-03-03 14:29:02.0
OK International (www.okinternational.com) has launched a new soldering system for PV tabbing and bussing applications proven to reduce micro cracking. The PS900 with specially designed hoof tip geometry optimizes the power delivered to the solder joint while it’s temperature-sensitive heater ensures low temperature soldering thus minimizing thermally induced stresses on cell surfaces.
Industry News | 2015-01-20 16:51:31.0
Viscom announced today that it will exhibit in Booth #1017 at the IPC APEX EXPO, scheduled to take place Feb. 24-26, 2015 at the San Diego Convention Center in California. Viscom’s inspection experts will present the most advanced and comprehensive SPI, AOI and X-ray portfolio on the market.
Industry News | 2003-06-13 10:10:58.0
By combining PacTech's electroless under bump metallization (UBM) processing with DEK's advanced mass imaging systems to create the solder bumps, users can implement a wafer-level, SMT-compatible flip chip assembly process.
Industry News | 2018-10-18 08:42:00.0
Reflow oven zone temperature set up and thermal profile
Technical Library | 2015-12-23 16:57:27.0
The onset of copper barrel cracks is typically induced by the presence of manufacturing defects. In the absence of discernible manufacturing defects, the causes of copper barrel cracks in printed circuit board (PCB) plated through holes is not well understood. Accordingly, there is a need to determine what affects the onset of barrel cracks and then control those causes to mitigate their initiation.The objective of this research is to conduct a design of experiment (DOE) to determine if there is a relationship between PCB fabrication processes and the prevalence of fine barrel cracks. The test vehicle used will be a 16-layer epoxy-based PCB that has two different sized plated through holes as well as buried vias.
Technical Library | 2018-09-21 10:12:53.0
Moisture accumulates during storage and industry practice recommends specific levels of baking to avoid delamination. This paper will discuss the use of capacitance measurements to follow the absorption and desorption behaviour of moisture. The PCB design used in this work, focused on the issue of baking out moisture trapped between copper planes. The PCB was designed with different densities of plated through holes and drilled holes in external copper planes, with capacitance sensors located on the inner layers. For trapped volumes between copper planes, the distance between holes proved to be critical in affecting the desorption rate. For fully saturated PCBs, the desorption time at elevated temperatures was observed to be in the order of hundreds of hours. Finite difference diffusion modelling was carried out for moisture desorption behaviour for plated through holes and drilled holes in copper planes. A meshed copper plane was also modelled evaluating its effectiveness for assisting moisture removal and decreasing bake times. Results also showed, that in certain circumstances, regions of the PCB under copper planes initially increase in moisture during baking.
Industry News | 2011-12-30 23:26:12.0
Nihon Superior has highlighted the effectiveness of Cu and Ni as the essential elements in forming a stable IMC layer in lead-free soldering.
