Full Site - : servo problem (Page 12 of 20)

Universal GSM 2

Electronics Forum | Tue Oct 14 14:08:22 EDT 2014 | dilogic

No, each card in LP servo rack drives only one motor. But there is an servo cotnroller board (actually 3 of them) in the VME rack (where all computers are). Third one from the left(slot13) controls head2 theta and z axis. That might be a cause of you

Zevatech Z Axis fault

Electronics Forum | Wed Jul 01 13:41:25 EDT 2009 | jlawson

Are you sure it is the Z axis, and not the > rotation, I had one machine which often did > something similar, it would buzz loudly, > especially if you touched or applied rotation > pressure to the gear belt which rotates the > head. It never ca

CP-65: Servo alarm C Axis, Servo overflow?

Electronics Forum | Tue Mar 23 18:02:54 EDT 2010 | rodrigo

Hi all, We're setting up a cp-65 and we're finding some issues with it. It has a missing 1st solenoid/switch and some nozzle valves on the cam. The biggest issue is this C axis servo error. The proper data was set to a cam speed of 250 (25%). That's

TR2100 problems? need help?

Electronics Forum | Sun Oct 18 11:48:50 EDT 2009 | Rul

Problems found are the machine frequent freeze suddenly and produce error message when homing the machine: servo devices failed ... Action taken. Change the pc with another working machine. result= same problem happen. check the fuse at circuit of t

Panasonic servodrivers in Tenryu again

Electronics Forum | Sat Jun 22 05:40:36 EDT 2013 | lkavan

Hi friends, I am sorry that I boring you again, but I hope somebody can help me... I have a problem with servodrivers Panasonic MSD5A3P1EA in my Tenryu MT5530. Some servo loops are unstable, motor is shaking. It is problem with driver, when I change

TDK RX11 Machine

Electronics Forum | Wed Dec 03 23:59:31 EST 2003 | masr

Basically the problem detail is, can't read the encoder reader from the motor, I swap the servo pack, the controler cards from the pc, the output cards from the plc, the motor and still have the problem!

MyData Y wagon shudder

Electronics Forum | Wed Mar 23 23:00:17 EST 2005 | pmd

Problem solved. Thru the help of MyData support we have determined that older MyDatas have a software issue with the servo drivers. A newer rev of driver will fix this problem.

mydata 19 error

Electronics Forum | Thu Feb 13 09:52:03 EST 2014 | rgduval

Start by getting into the maintenance menu, and manually installing the Servo program for all MOTs. If they install fine, you can check the Z-motor while you're in the maintenance menus. Make sure that the z-locks are unlocked before checking the

Skew error at axis G1F-Y

Electronics Forum | Wed Oct 26 05:44:39 EDT 2022 | spacecase

Hello all, I was looking at a Samsung SM421-f component placing machine and it's throwing up an error that was not described in the troubleshooting guide. Anytime I try to move the camera or home it the machine stops and the screen says that a skew e

Universal Instruments Genesis Servo Amp

Electronics Forum | Thu Feb 21 05:34:21 EST 2019 | reckless

I have 2 older genesis machines currently down due to VRM Servo issues. I'm debating whether its better to stock up on some spares as I'm finding spares cheap currently. How often do they go out and how long should they last? Any other parts that


servo problem searches for Companies, Equipment, Machines, Suppliers & Information

SMTAI 2024 - SMTA International

Component Placement 101 Training Course
PCB Handling Machine with CE

Software for SMT placement & AOI - Free Download.
High Throughput Reflow Oven

Training online, at your facility, or at one of our worldwide training centers"