Electronics Forum | Tue Sep 18 10:52:14 EDT 2012 | sarason
Sounds like a plan. The usual way is to count how many you use on the job either by pre-calculation. Or how many clicks the machine counts and save the data before switch off, then drop it back into a spread sheet. This depends very much on the mach
Electronics Forum | Tue May 08 19:28:29 EDT 2001 | mparker
Received my copy of the standard about a month ago. Seems straightforward and gets away from the percentage nightmare. Mark Twain said it best with "There are 3 kinds of lies in this world - lies, damn lies and statistics!!" Now I have some nagging
Electronics Forum | Thu Aug 25 11:33:32 EDT 2005 | slthomas
I suppose it depends on your layout software. My weak recollection of what PowerPCB does is allow you to set up rules as far as spacing and where parts are placed, then you run the rule check, er something like that. As far as "Also what I"m thinkin
Electronics Forum | Thu Jul 18 12:44:24 EDT 2013 | ericrr
after checking two computers, did not find it. However after using "google" found it in a flash. (less than 0.22 seconds) using a spreadsheet. how about this for resistor & capacitors with 4mm pitch, all measurements in millimeters. cell A1 "input
Electronics Forum | Thu Jun 03 01:26:06 EDT 2021 | deanm
This may seem off the wall but I've seen it work in the past. It is a visual management system without the need for barcodes or spreadsheets. Obtain quantities of different colored clothespins. When a reel is taken out of inventory, attach a colored
Electronics Forum | Thu Aug 15 15:44:46 EDT 2002 | dragonslayr
You can't control what you don't measure. You have provided very little detail other than post reflow costs are high. What defects are attributed to problems experienced prior to reflow? Are these random or recurring defects? You will need to put ea
Electronics Forum | Mon Jan 04 11:32:59 EST 1999 | Chrys
| Anyone have any experience with ECD's Waverider/MOLE profiling equipment? If so, were they positive experiences? | I use ECD's mole for profiling in the wave and a KIC for profiling in reflow. I like the KIC a whole lot better for a couple of re
Electronics Forum | Mon Jan 04 22:59:23 EST 1999 | Kris Ewen
I'd like to add something about the ECD product. During a past work term (I'm a a co-op student) in an SMA plant, I worked extensively with the Super MOLE Gold in developing the reflow profiles for high-mix, low-volume production. I was 'married' t
Electronics Forum | Mon Sep 13 16:29:17 EDT 1999 | Earl Moon
| | Dearest Jennifer, | | | | Ooooops! Forgot which one I was writing - please forgive me. Ah yes, SMT and you, you see even we don't get it right. If you combined all our answers, you would get close - as close as when we get frustrated. | | | | A
Electronics Forum | Fri Jan 28 12:18:32 EST 2005 | Chunks
Your best bet is to do a decision making matrix. Each company has so many different criteria�s it's hard to pick out which one might be important to yours. Simply pick out your top 5 paste manufactures. Next decide what your "Eliminators" are - th
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China
Phone: 0755-33578694