Full Site - : super-mole (Page 2 of 3)

Super Mole Thinline RS232 Cable

Electronics Forum | Fri May 02 11:11:49 EDT 2008 | lon_sanders

The cable required for the Thinline has to work as a true RS232 interface as the unit uses all the capabilities of RS232. You will have several problems with substitutes. These cables (part number e00-2787-26) are still avaliable from ECD, the home o

Super Mole Gold Batter charger lost, please help!!!

Electronics Forum | Mon Sep 20 21:37:14 EDT 2004 | Hayden

Hi folks, I currently use the supermole gold to do all my SMT relfow profiles. However, I've lost the charger for the supermole battery pack. If someone also use this tool and have their charger handly, would you please look at your charger and give

Super Mole Gold Batter charger lost, please help!!!

Electronics Forum | Wed Sep 22 12:23:11 EDT 2004 | Peter Barton

FYI Label on the back of my charger says the following: Pt. No. WD23D200KCN PSU E31-0900-21 Input 230 V AC Output 9V DC, 0.2A 1.8VA Ours is of course United Kingdom type, even if the mains plug is European and requires an adaptor. Not too sure a

Super Mole Thinline RS232 Cable

Electronics Forum | Mon Apr 21 23:08:03 EDT 2008 | dman97

Hi, Does anyone know what kind of cable the thinline profiler uses? I recently acquired one of these profilers, but it came with no cables. I went out and bought a female to female serial cable, but it did not work. It will not communicate with my P

Super Mole Thinline RS232 Cable

Electronics Forum | Fri Apr 25 13:40:37 EDT 2008 | flipit

If you know a little about electronics, you can probably figure it out. Or just buy one from Mole. Do you have software? More than likely you will have receive, ground, and transmit. Open up the Mole if you can and look for the RS232 chips(Max232

Custom Super M.O.L.E. Thermal Protective Enclosure ?

Electronics Forum | Fri Nov 20 17:17:19 EST 2009 | Flipit

I have done this for the Datapaq and it worked well. The SlimKic uses a yellow thermal blanket material. It is called Pyropel. You can get it at McMasterCarr. I think McMasterCarr calls it polyimid foam insulation part number 93015K64 of 3/16 thi

Re: Reflow Profile

Electronics Forum | Wed Nov 25 21:23:29 EST 1998 | Dave F

| I like to know under what conditions the reflow profile of a solder paste is taken? Bare board, board with the solder paste, or board with high melt solder paste? | John: None of the above. The two key variables that determine the reflow tempera

Super M.O.L.E or Slim KIC 2000 for oven profiling?

Electronics Forum | Tue Jul 30 11:30:23 EDT 2002 | slthomas

We currently use the SuperMole and generally speaking it's a nice tool and gives us the information we need. The software could use some work, though. When you create a file for a new profile, you have to input a "time above" temperature for your

Rectangular uBGAs with 1 raised edge after reflow

Electronics Forum | Wed Sep 05 14:51:47 EDT 2001 | gdstanton

Well, it appears after running both a bare and populated PWB we were seeing flux exhaustion on the uBGA. The problem apparently resulted by a recent maintenance effort where the air blowers in the reflow oven were replaced. The blower replacement m

Non-wetting: PTH on double-side reflow

Electronics Forum | Wed Apr 06 11:10:47 EDT 2005 | smt_rookie

We process a double-side reflow board (10 ups). Chips and IC's on the bottom side while chips, IC's plus thru-hole connectors and IC sockets on top side (bottom side first then top side reflow). In the past, we were not encountering any soldering pro


super-mole searches for Companies, Equipment, Machines, Suppliers & Information