Parts & Supplies | Pick and Place/Feeders
The electric double tape feeder holds two 8mm reels in the space(17mm) of a single traditional tape feeder. This doubles the feeder capacity of the machine which means there is a greater chance of clustering boards into a single feeder setup. It also
Parts & Supplies | SMT Equipment
40092060 CONVEYOR BELT IN OUT XL FX-ERA(ELECTRIC) 40011058 CONVEYOR BELT EX GX-6 for JUKI 2050~2080 40046521 TIMING BELT T GX-6 T belt for 2070 2080 40092060 CONVEYOR BELT IN OUT XL FX-ERA (ELECTRIC) 40092061 CONVEYOR BELT JOINT XL 40092062 CON
Technical Library | 2012-12-17 22:05:22.0
Package on Package (PoP) has become a relatively common component being used in mobile electronics as it allows for saving space in the board layout due to the 3D package layout. To insure device reliability through drop tests and thermal cycling as well as for protecting proprietary programming of the device either one or both interconnect layers are typically underfilled. When underfill is applied to a PoP, or any component for that matter, there is a requirement that the board layout is such that there is room for an underfill reservoir so that the underfill material does not come in contact with surrounding components. The preferred method to dispensing the underfill material is through a jetting process that minimizes the wet out area of the fluid reservoir compared to traditional needle dispensing. To further minimize the wet out area multiple passes are used so that the material required to underfill the component is not dispensed at once requiring a greater wet out area. Dispensing the underfill material in multiple passes is an effective way to reduce the wet out area and decrease the distance that surrounding components can be placed, however, this comes with a process compromise of additional processing time in the underfill dispenser. The purpose of this paper is to provide insight to the inverse relationship that exists between the wet out area of the underfill reservoir and the production time for the underfill process.
Parts & Supplies | Assembly Accessories
JUKI750/60 Belt E2017725000 CONVEYOR BELT S 750/60 In/out Belt E2016725000 CONVEYOR BELT C 750/60 Center Belt E3023725000 TIMING BELT THETA 750/60 T Belt E2308725000 TIMING BELT (YB) 750/60 YB Belt E2306725000 TIMING BELT (YA) 750/60 YA Belt E2
Parts & Supplies | SMT Equipment
03008702-01 VACUUM PLATE COMPLETE f. short Sleeve (red) 03008853-03 STOP CABLE COMPL. F. CENTER COVER 03008862-03 NOZZLE / NP-ADJUSTMENT TH 03008951-01 CABLE: EXTENSION IN/OUT SIDE 03009198S01 PANEL COMPLETE WITH CABLE / X-SERIES
Used SMT Equipment | Pick and Place/Feeders
Make: Assembleon Model: MG5 Vintage: 2011 Details: Fixed Feeder Banks Pneumatic FT/CL Feeder Interface (Feeders Sold Separetely) 2×24 Position Fixed Feeder Bank Front Single Placement Beam with 5 Heads Front Line Array Camera with Side Light (For
Parts & Supplies | Pick and Place/Feeders
Samsung SM Feeder Calibration JIG SMT Feeder Calibration Specification: Dimension:500 x 350 x 550 mm , L x W x H Type:Electric / Pneumatic Monitor : 12” LED display, with cross mark Camera : CCD, 50 times magnification Appliable:Samsung SM se
Parts & Supplies | Pick and Place/Feeders
Samsung CP Feeder Calibration JIG SMT Feeder Calibration Specification: Dimension:500 x 350 x 550 mm , L x W x H Type:Pneumatic / Manual Monitor : 12” LED display, with cross mark Camera : CCD, 50 times magnification Appliable:Samsung CP seri
Parts & Supplies | Pick and Place/Feeders
FUJI NXT Feeder Calibration JIG for SMT pick and Place Equipment It is essential for this equipment that enhanced productivity , installation and quality improvement As the high efficiency vision camera is asked in order to investigate precisel
Parts & Supplies | Pick and Place/Feeders
Samsung CP Feeder Calibration JIG SMT Feeder Calibration Specification: Dimension:500 x 350 x 550 mm , L x W x H Type:Pneumatic / Manual Monitor : 12” LED display, with cross mark Camera : CCD, 50 times magnification Appliable:Samsung CP serie