Industry Directory | Manufacturer's Representative
Manufacturing Representative serving North Carolina, South Carolina, and Virginia.
Electronics Forum | Wed Feb 22 08:02:56 EST 2006 | dj44
I was looking for an stencil design for a 0.5mm pitch uBGA. Pad size is 0.38mm in diameter. We have been using 5mil stencil with type 3 no clean paste. What size aperture should we be using? Any suggestions?
Electronics Forum | Wed Feb 22 10:00:58 EST 2006 | dougs
We've just set up a couple of products with 0.5mm pitch uBGA devices on them, i went for 5thou thick, laser cut nickel (to aid paste release) square pads same size as the diameter of the uBGA pads. Or you could go to a 4 thou nickel stencil, better
Industry News | 2016-08-19 05:00:52.0
If you have a process problem, let NPL Defect of the Month Video help you team
Technical Library | 2023-07-25 16:50:02.0
Some of the new handheld communication devices offer real challenges to the paste printing process. Normally, there are very small devices like 01005 chip components as well as 0.3 mm pitch uBGA along with other devices that require higher deposits of solder paste. Surface mount connectors or RF shields with coplanarity issues fall into this category. Aperture sizes for the small devices require a stencil thickness in the 50 to 75 um (2-3 mils) range for effective paste transfer whereas the RF shield and SMT connector would like at least 150 um (6 mils) paste height. Spacing is too small to use normal step stencils. This paper will explore a different type of step stencil for this application; a "Two-Print Stencil Process" step stencil. Here is a brief description of a "Two-Print Stencil Process". A 50 to 75 um (2-3 mils) stencil is used to print solder paste for the 01005, 0.3 mm pitch uBGA and other fine pitch components. While this paste is still wet a second in-line stencil printer is used to print all other components using a second thicker stencil. This second stencil has relief pockets on the contact side of the stencil any paste was printed with the first stencil. Design guidelines for minimum keep-out distances between the relief step, the fine pitch apertures, and the RF Shields apertures as well relief pocket height clearance of the paste printed by the first print stencil will be provided.
Technical Library | 2023-07-25 16:25:56.0
This paper address two significant applications of stencils in advance packaging field: 1. Ultra-Thin stencils for miniature component (0201m) assembly; 2. Deep Cavity stencils for embedded (open cavity) packaging. As the world of electronics continues to evolve with focus on smaller, lighter, faster, and feature-enhanced high- performing electronic products, so are the requirement for complex stencils to assemble such components. These stencil thicknesses start from less than 25um with apertures as small as 60um (or less). Step stencils are used when varying stencil thicknesses are required to print into cavities or on elevated surfaces or to provide relief for certain features on a board. In the early days of SMT assembly, step stencils were used to reduce the stencil thickness for 25 mil pitch leaded device apertures. Thick metal stencils that have both relief-etch pockets and reservoir step pockets are very useful for paste reservoir printing. Electroform Step-Up Stencils for ceramic BGA's and RF Shields are a good solution to achieve additional solder paste height on the pads of these components as well as providing exceptional paste transfer for smaller components like uBGAs and 0201s. As the components are getting smaller, for example 0201m, or as the available real estate for component placement on a board is getting smaller – finer is the aperture size and the pitch on the stencils. Aggressive distances from step wall to aperture are also required. Ultra-thin stencils with thicknesses in the order of 15um-40um with steps of 15um are used to obtain desired print volumes. Stencils with thickness to this order can be potential tools even to print for RDLs in the package.
SMTnet Express, June 23, 2022, Subscribers: 25,382, Companies: 11,579, Users: 27,300 █ Electronics Manufacturing Technical Articles Effect of Nano-Coated Stencil on 01005 Printing ... The most important attribute of a stencil is its
winsouce.jpg)
.gif)