Industry Directory | Manufacturer
A specialty chemical and material manufacturer catering to the bare board PCB industry. The company offers a wide range of chemical products that range from Photoresist strippers to Electroless Copper to a variety of final finish products.
Supplier of plasma solutions for surface finishing and coating.
New Equipment | Solder Materials
Proposal Pro Contra VOC (100% alcohol) 385-D 390-RX-HT 323-ITM Moderate preheating Reliable Very known technology
New Equipment | Solder Materials
To meet the increased demands imposed by the higher operating temperatures involved in successful lead free soldering, DKL Metals have released new flux products designed specifically for this environment. A selection of the most popular, incorporati
Electronics Forum | Tue Nov 11 21:21:49 EST 2003 | Dean
What do you guys do with your old, used VOC free flux? Can you just send it down the drain? Or is it considered hazardous, and should be disposed of accordingly? Thanks for your replies.
Electronics Forum | Wed Nov 12 08:10:47 EST 2003 | davef
As a minimum, you should observe the recommendations for disposal in your flux supplier's MSDS. For one VOC-Free Flux, the MSDS says something like: Waste Disposal Methods: Scrap material may be disposed of, by a licensed waste disposal company or
Used SMT Equipment | Soldering - Wave
USI Optima spray fluxer. Was mounted internally in an Electrovert wavesolder system. This fluxer had limited use and was used with a VOC free, No Clean flux so very clean.
Industry News | 2003-02-17 08:40:25.0
To Meet Government Environmental Standards and Individual Company Policies, While Satisfying Production Requirements
Industry News | 2010-02-18 21:26:02.0
Minneapolis, MN - The SMTA is pleased to announce several new webinars coming up in March. Webinars are 60 to 90 minute online presentations comparable to a conference session. In response to industry-wide budget cuts and travel restrictions, SMTA has committed to increasing its online programming to better accommodate member needs for technical exchange.
Technical Library | 1999-05-07 11:44:26.0
In 1990 the United States Environmental Protection Agency Issued the Clean Air Act. The Clean Air Act and subsequent amendments are designed to limit the use of chemicals that contain volatile organic compounds (VOCs). The document goes into great detail setting limits for allowable VOC emissions for different industries.
Technical Library | 1999-04-26 15:51:30.0
The goal of the flux evaluation was to identify one product that would meet the needs of all SICN's wave solder products and processes while producing high quality assemblies. At the outset of the evaluation, it was unclear whether a single flux chemistry could satisfy such a broad range of demands, particularly because SICN's utilization of less aggressive, low-impact chemicals.
SonoFlux 2000F is a stationary spray fluxing system for coating Printed Circuit Boards with a uniform thin film layer of flux. Features include excellent through hole penetration for maximum top side fill, non-clogging, self cleaning ultrasonic nozzl
Printed Circuit Board Protection Methods - Conformal Coating Encapsulants Potting Module Sealing Low Pressure Molding
Non-Contact Streaming Technology Enhances the Dispense Process News Forums SMT Equipment Company Directory Calendar Career Center Advertising About FREE Company Listing! Non-Contact Streaming Technology Enhances the Dispense
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/adhesive-dispensing-systems/products/foaming-systems/foammelt-dispensing-system
control for consistent adhesive viscosity Minimize VOC emissions with solvent-free assembly In This Section Product Type Foaming Systems FoamMelt Dispensing System FoamMix®
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2022/06/Optimizing-Reflowed-Solder-TIM-sTIMs-Processes-for-Emerging-Heterogeneous.pdf
backside (initial studies show no effect on lids) Flux formulation optimization, using halogen-free, ultralow residue and VOC-free types, as flux is often used as tackifier as well as a reducing agent CSAM and 3D x-ray to determine void location in x, y and
.gif)
