New Equipment | Assembly Services
BEST can provide you with analysis services for your BGAs using x-ray equipment. We rework thousands of BGAs and POPs every year, therefore, we have the expertise in BGA X-ray inspection. BEST can be your outsourced BGA x-ray inspection source for o
New Equipment | Rework & Repair Services
BEST offers contract PCB rework services. If you get in bind and need resources to perform difficult repairs or if the volume of work ahead of you is too extreme to get through in the deadline at hand then consider BEST PCB rework services. If you th
Electronics Forum | Thu Apr 23 15:46:08 EDT 2009 | ccross
During initial profiling we shoot for 15% or less voiding on our BGAs. During production runs we consider voids under 15% to be ok. Voiding between 15%-25% we string tag and pay more attention to during test. Over 25% we consider a reject.
Electronics Forum | Thu Apr 23 00:27:06 EDT 2009 | josephkhiew
25% void (total pcba inspected is 15 boards, each board has 2 BGAs and each BGA has 64 balls). Referring IPC-7095 stated that there is no evidence or empirical data that indicates that voids within ball will cause failure. We would appreciate if y
Industry News | 2003-06-10 08:16:44.0
The following text describes the application of NWA Quality Analyst to quality control in the assembly of electronic components.
Industry News | 2018-10-18 08:17:09.0
How to Prevent Solder Joint Voiding and Cold Solder Defects during the SMT Reflow Process
Technical Library | 2023-01-17 17:22:28.0
The impact of voiding on the solder joint integrity of ball grid arrays (BGAs)/chip scale packages (CSPs) can be a topic of lengthy and energetic discussion. Detailed industry investigations have shown that voids have little effect on solder joint integrity unless they fall into specific location/geometry configurations. These investigations have focused on thermal cycle testing at 0°C-100°C, which is typically used to evaluate commercial electronic products. This paper documents an investigation to determine the impact of voids in BGA and CSP components using thermal cycle testing (-55°C to +125°C) in accordance with the IPC- 9701 specification for tin/lead solder alloys. This temperature range is more typical of military and other high performance product use environments. A proposed BGA void requirement revision for the IPC-JSTD-001 specification will be extracted from the results analysis.
Technical Library | 2020-01-28 00:23:58.0
This paper explores new advances in the reflow soldering process including vacuum technology and warpage mitigation systems. The first topic for discussion will be the implementation of a vacuum process directly in a conventional inline soldering system. The second topic presented is the mitigation of warpage on substrates or wafers.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Teresa Rowe, IPC director of assembly standards, highlights several revisions to IPC J-STD-001F, Requirements for Soldered Electrical and Electronic Assemblies and IPC-A-610F, Acceptability of Electronic Assemblies. The documents have been updated to
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Events Calendar | Wed Mar 08 00:00:00 EST 2017 - Wed Mar 08 00:00:00 EST 2017 | San Diego, California USA
San Diego Chapter - Minimizing Voiding in Bottom-Terminating Components
Events Calendar | Thu Oct 03 00:00:00 EDT 2019 - Thu Oct 03 00:00:00 EDT 2019 | ,
IPC Tech Ed Webinar Series: Ball Grid Array (BGA) and Bottom Termination Component (BTC) Design and Assembly Challenges: Reflow Profiling to Achieve Low Defect Rates and Successful Assembly! – Part 2
SMTnet Express, January 5, 2014, Subscribers: 23,708, Members: Companies: 14,158 , Users: 37,476 The Last Will And Testament of the BGA Void Dave Hillman, Dave Adams, Tim Pearson, Brad Williams, Brittany Petrick, Ross Wilcoxon - Rockwell Collins
SMT Express, Volume 2, Issue No. 3 - from SMTnet.com Volume 2, Issue No. 3 Thursday, March 16, 2000 Featured Article Return to Front Page Curtailing Voids in Fine Pitch Ball Grid Array Solder Joints by Gary Morrison and Kevin Lyne
| https://www.eptac.com/blog/are-voids-in-solder-joints-really-an-issue
Are Voids in Solder Joints Really an Issue? Looking for solder training standards, manuals, kits, and more? Visit soldertraining.com Training Training Materials Locations Resources Ask Helena
Imagineering, Inc. | https://www.pcbnet.com/blog/what-are-lamination-voids-in-pcb-manufacturing/
What Are Lamination Voids in PCB Manufacturing? | Imagineering, Inc. Skip to main content Resources Support Contact Us FAQs Live Chat My Account 847-806-0003 Menu PCB Capabilities Fabrication Technology Roadmap Materials Available HDI Tolerances Certifications
