.jpg)
New Equipment | Solder Materials
LOCTITE GC 10 is a halogen free, zero halogens added, no-clean, low voiding, Pb-free solder paste specially formulated to provide added long term stability over a wide range of temperature conditions. The enhanced paste stability created through its
Electronics Forum | Thu Sep 02 05:12:15 EDT 2004 | doi
I am using a triad connector and have problem with wetting at both connector latches.Observed that the leads have very good shiny wetting however concerning the latches the solder just seem to disappear to thin airafter reflow.The connector has a gui
Electronics Forum | Thu Sep 02 09:51:53 EDT 2004 | davef
We see latches from some suppliers that just are not solderable. Usually the nickel plate on the latch is poor, allowing the nickel to corrode, and requiring a more active flux [if you're lucky]. But lots of times, you end-up with partial wetting,
Industry News | 2011-02-24 20:35:03.0
The SMTA is pleased to announce the program for the 2011 International Conference on Soldering and Reliability being held May 3-6 in Toronto, Ontario, Canada.
Industry News | 2010-09-13 15:36:15.0
IPC — Association Connecting Electronics Industries® has released IPC-1601, Printed Board Handling and Storage Guidelines. The industry's sole standard on the handling, packaging and storage of printed boards, IPC-1601 provides users with guidance on how to protect printed boards from contamination, physical damage, solderability degradation, electrostatic discharge and moisture uptake.
Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2012-12-17 22:05:22.0
Package on Package (PoP) has become a relatively common component being used in mobile electronics as it allows for saving space in the board layout due to the 3D package layout. To insure device reliability through drop tests and thermal cycling as well as for protecting proprietary programming of the device either one or both interconnect layers are typically underfilled. When underfill is applied to a PoP, or any component for that matter, there is a requirement that the board layout is such that there is room for an underfill reservoir so that the underfill material does not come in contact with surrounding components. The preferred method to dispensing the underfill material is through a jetting process that minimizes the wet out area of the fluid reservoir compared to traditional needle dispensing. To further minimize the wet out area multiple passes are used so that the material required to underfill the component is not dispensed at once requiring a greater wet out area. Dispensing the underfill material in multiple passes is an effective way to reduce the wet out area and decrease the distance that surrounding components can be placed, however, this comes with a process compromise of additional processing time in the underfill dispenser. The purpose of this paper is to provide insight to the inverse relationship that exists between the wet out area of the underfill reservoir and the production time for the underfill process.
Precise lines are dispensed to fill an area on a heat sink. At the end of this video, you can see a demo of placing a glass slide on top of the dispensed material to see uniformity of the area. http://www.nordsonasymtek.com
| http://etasmt.com/cc?ID=te_news_industry,24564&url=comment
How to Prevent Non-Wetting Defect during the SMT Reflow Process-SMT Technical-Reflow oven,SMT Reflow Soldering Oven-cmsadmin Home About
| https://www.eptac.com/faqs/ask-helena-leo/ask/bridging-two-adjacent-pins-on-an-ic
Bridging Two Adjacent Pins on an IC - EPTAC - Train. Work Smarter. Succeed Looking for solder training standards, manuals, kits, and more
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
winsouce.jpg)
