Pre-scored Automatic PCB Depaneling Machine with Large LCD Display Specification: Power :AC 110 / 220 V 50 / 60HZ Dimension :780 × 400 × 450mm Blade Route :430mm / Max Blade Speed :500mm / sec Down- Blade Size :500 mm Cutting length :460mm Mac
The NexJet® 8 Jetting System with patented ReadiSet™ Jet Cartridge offers increased jet frequency combined with advanced consumable management - it's as easy as ReadiSet and Jet. ReadiSet Jet Cartridge reduces operator training time, cost-of-owner
Electronics Forum | Wed Oct 10 13:49:12 EDT 2001 | stepheno
I recently started at a new company. They have a variety of bare PCB's and most have aprox. 20 variations. Maybe about 1/3 of each board on average are non-populated locations. They buy one stencil for each PCB but then use scotch tape to block of
Electronics Forum | Wed Oct 10 20:35:17 EDT 2001 | djarvis
Stephen, I don't understand this at all mate. 1. If you don't place a QFP and get bridging across the bare pads, you were gonna get absolutely horrendous bridging if you did put one down. That points to poor printer set up or stencil design or both
Used SMT Equipment | Screen Printers
Hello and thank you for your interest in our MPM AP36 Stencil Printer. The machine was recently taken out of an SMT Manufacturing facility which closed. It is located at our facility in Boston, MA where it was powered up, cycled, and zero by an MPM S
Used SMT Equipment | Screen Printers
Hello and thank you for your interest in our MPM UP2000 Hie Stencil Printer For Sale. The machine was recently taken out of an SMT Manufacturing facility which closed. It is located at our facility where it was powered up, cycled, and zero reset by a
Industry News | 2011-01-12 17:40:04.0
Check out these Show Highlights, Ways to Save, Networking and Educational Opportunities, and Exhibition Preview.
Industry News | 2011-03-21 12:41:15.0
Count On Tools Inc. will hold a sweepstakes during the IPC APEX EXPO. Attendees can sign up for the drawing at www.cotinc.com/20years.
Parts & Supplies | SMT Equipment
9498 396 00198 00196 00197 Philips TTF peel off module Part No. Description 5322 214 91436 BOARD, PIPETTE 5322 214 91038 TRANSPORT CONTROLLER FCM 5322 216 04091 TRANSP CONTRL ACM-AX201 5322 216 04095 #REF! 5322 216 04095 #REF! 5322 21
 (2)_1.JPG)
Parts & Supplies | Pick and Place/Feeders
Pressure cap for 8 mm Tape Cover art. 9498 396 01387 (old part. 5322 442 01529) Part No. Description 5322 214 91436 BOARD, PIPETTE 5322 214 91038 TRANSPORT CONTROLLER FCM 5322 216 04091 TRANSP CONTRL ACM-AX201 5322 214 91771 CONTROLLER BVM 949
The NexJet® 8 System with ReadiSet™ Jet Cartridge offers increased jet frequency combined with advanced consumable management - it's as easy as ReadiSet and Jet. Read more at http://www.nordsonasymtek.com/nexjet
Broader scope, the latest ultra-small SMD components (01005) count, the series is as follows: These are the components package specifications. Functions: 1, Empty chip detection capabilities SMD chip counter, the job is simple, positive and neg
Career Center | BANGALORE, Karnataka India | Quality Control
New Model Evaluation • Testing & Evaluation of New TV models as per the relavant standards & release the defect free product for Mass Production • Measurement of audio parameters like Max out put, distotion, S/N ratio, hum, buzz etc • To conduct aud
Career Center | , | Engineering,Maintenance,Production
Production Planning ~ Supply Chain Management ~ Productivity Management ~ Sub Contracting Management ~ Process Quality Management ~ Process innovation & Lean Mfg ~ Cost efficiency Management ~ Manpower Management ~Multi Skilling & Training, Six Sigma
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/industrial-coating-systems/application-solutions/automotive-assembly/power-train
: The Zero-Cavity dispense valve creates a cut-off point at the very tip of the valve. This prevents any air from reaching the residual material, circumventing the nozzle curing issue. Bead Placement
| https://unisoft-cim.com/pins-displayed-on-off-by-part-number.html
. How to use the library .OPR file method: Create a .OPR library file with the part numbers you wish to edit. To automatically turn off all the component pins for all the components in a part number use the following command in the second field
winsouce.jpg)