Electronics Forum | Tue Oct 09 20:27:13 EDT 2001 | davef
That�s a 672 BALL BGA, bud!!! It�s a BIG Mutha!!! [I know. I know. For some reason suppliers call balls "pins".] Let�s focus on: * Clarifying the units on your PCB and aluminum plate thickness measurements. * Describing your use of the aluminum pl
Electronics Forum | Thu Oct 11 22:25:50 EDT 2001 | davef
Bruce I�m with yall. Designers and fabricators say �pins�. You say: * BGA pins are 1mm [0.039�] pitch. * BGA pads are 0.4mm [0.0157�] diameter. * BGA pins are 0.6 mm [0.024�] side-to-side. * Board thickness is ~0.4 mm [0.015�] First, as you can
Electronics Forum | Tue Jul 28 09:15:49 EDT 1998 | Justin Medernach
| We are about to run our first BGA devices and would appreciate some confirmation on a few points. | First some details: | PCB & Device: | ============= | 1) 16 layer (4 power, 4 gnd, 8 signal) | 2) gold on nickel finish | 3) ceramic BGA with eutec
Electronics Forum | Tue Jul 28 17:23:58 EDT 1998 | Robert Steltman
| | We are about to run our first BGA devices and would appreciate some confirmation on a few points. | | First some details: | | PCB & Device: | | ============= | | 1) 16 layer (4 power, 4 gnd, 8 signal) | | 2) gold on nickel finish | | 3) ceramic
Electronics Forum | Fri Dec 11 09:06:57 EST 1998 | Tom
| Has any body tried reflowing QFP's on both sides of a board. | GCollier Yes we do that quite often, we are using QFP132 with 0.5mm pitch in pure reflow process for both sides (no glue). It works well, the only problems we have seen was wiht compon
Electronics Forum | Fri Oct 14 10:55:07 EDT 2005 | Mika
We have a simular problem with Ni/Au; especially whith pcb thickness more than 1.8mm. Note: These boards have been through reflow process also. 1.)Is there a maximum board thickness where it would be almost impossible to get a decent hole fil? 2.)Wi
Electronics Forum | Thu Jun 27 03:03:57 EDT 2019 | SMTA-David
Hi, I have a small assembly line that consists of a Semi-Automatic Stencil machine, a Samsung Pick and Place, a small IR reflow oven and a wave soldering machine. The reflow oven is presenting the biggest bottleneck. The machine is a small IR (T960
Electronics Forum | Sun Dec 05 22:43:27 EST 1999 | dreamsniper
Charley, Though my reply is quite late, it might be a good info for you and i hope that this info could help or could provide you some views. Some companies practice at least 1 board gap, which means the length of the pcb you are currently loading,
Electronics Forum | Tue Jan 14 11:53:44 EST 2020 | avillaro2020
Hi Phil, thanks. I am successful using the same connector on small thinner boards 2-2.5kg) i cant make it work, tried all kinds of profiles with vapour phase but to no avail. Yes you read it right 4.3-6.3mm pcb thickness and 2-2.5Kg. And it is 44 lay
Electronics Forum | Thu Jun 13 09:39:43 EDT 2019 | don_julio
Problem is I don't have a mesh belt (lesson learned). Our conveyor is pins. If I laid some scrap pcb's spanning the conveyor pins on the long dimension of the board, I'm confident it would sag. We get a bit of sag today in our 1.6mm thick boards whi
