Electronics Forum: 20mm feeder indexing sensor (Page 7 of 9)

Re: trailer tape length

Electronics Forum | Fri Jun 04 23:44:07 EDT 1999 | Dean

| | Has anyone had a problem with the trailer tape length being too short and causing placement machine to stop for parts exhaust (SMT parts)? I realize the EIA spec. is set for this length but would like to know what issues you have had. Thanks |

Re: trailer tape length

Electronics Forum | Sat Jun 05 07:47:47 EDT 1999 | Dave F

| | | Has anyone had a problem with the trailer tape length being too short and causing placement machine to stop for parts exhaust (SMT parts)? I realize the EIA spec. is set for this length but would like to know what issues you have had. Thanks

CP6 Performance

Electronics Forum | Wed Nov 16 10:48:23 EST 2005 | aj

Hi, There are a few different types of CP6 which I think the main differences are on the board loading side of things. To briefly answer your questions: 1.What is the actual CPH you are getting during production. There are a lot of variables to c

CSM Technical Question

Electronics Forum | Thu Oct 11 18:06:45 EDT 2007 | jmelson

Ohh, MY! Well, there is a whole block of info that is machine specific. There are 4 things on the main menu, the last one is the system calibrations. It has offsets between the primary reference (if you don't have vision, like mine) then the beam

Component attrition

Electronics Forum | Mon Dec 23 18:06:38 EST 2002 | jersbo

Tried and True is counting your components if there is any indication of loss... this is a great TOPIC... unfortunately there are many ways to lose components. Feeder setup,problems with a feeder while in the machine(IE mylar problems or wrong step)

CSM-84 pick and place machine.

Electronics Forum | Tue Feb 15 00:27:39 EST 2011 | jeffr

First clean and de-bur the hole in the nozzle, then try it again. If the Head does not pick up at the feeder, then moves to the dump position...it means that the Vacuum Sensor Board has detected that the nozzle vacuum is above the LOW threshold setti

Quad 4C nozzle changer

Electronics Forum | Wed Jun 01 11:02:57 EDT 2016 | claudea2

I have 3 used Quad 4Cs and the nozzle changer on one machine never worked. I decided to troubleshoot it this week. I repaired the changer by changing a defective optical sensor but I still get error 17 when I try a run-step nozzle 1, 2 or 3. Error 17

Fiducial recognition using laser

Electronics Forum | Sat Apr 03 16:39:15 EST 2004 | stefwitt

We had a similar system on the Siemens machines, quite some time ago. However, it was not a laser light but a LED and a fiber cable. Actually the center fiber or receiver was surrounded by a bundle of small fibers for the LED light source. You may al

Fuji parts out Signal for poka-yoke component replenishment

Electronics Forum | Tue Apr 03 00:37:51 EDT 2007 | grantp

Hi, I think the only solution would be to contact Fuji and ask if there is an interface to the machine to write software for it. I read somewhere that FujiTrax allows a IT system type connection which software could be written for. Another solution

Siemens S-27 Error Code Descriptions and Segment Issues

Electronics Forum | Wed Sep 10 07:42:52 EDT 2008 | lloyd

Can you provide a bit more info on your machine setup. I not full fimilar with the S-27 so a few points may not be relevant to your machine. Are you using Siplace Pro. Are you using the standard GF for the 0201 component. Do you have the component


20mm feeder indexing sensor searches for Companies, Equipment, Machines, Suppliers & Information

ISVI - Industrial Sensor Vision International Corporation
ISVI - Industrial Sensor Vision International Corporation

Industrial Sensor Vision International specializes in advanced camera technology of high resolution fast speed cameras for automation, AOI, 2-D/3-D, SPI inspection and wafer inspection.

Manufacturer

3 Morse Road 2A
Oxford, CT USA

Phone: +1 203 592 8723

Void Free Reflow Soldering

Training online, at your facility, or at one of our worldwide training centers"
SMT feeders

High Resolution Fast Speed Industrial Cameras.
Hot selling SMT spare parts and professional SMT machine solutions

Easily dispense fine pitch components with ±25µm positioning accuracy.
2024 Eptac IPC Certification Training Schedule

Software for SMT placement & AOI - Free Download.
PCB Depanelizers

Private label coffee for your company - your logo & message on each bag!