Electronics Forum: 360 smd adhesive (Page 1 of 13)

SMD adhesive

Electronics Forum | Mon Aug 29 18:14:20 EDT 2005 | OverTheHill

Good day, We use Loctite 3616 for securing SMD's to the PCB before wave. On rare occasions, we have to remove and replace the secured part. Our operators are having a diffucult time removing parts (large QFP's, etc). My questions to this forum: 1)

SMD adhesive

Electronics Forum | Tue Aug 30 10:01:55 EDT 2005 | slthomas

I haven't used that Loctite before as I've never printed adhesive, but you might try reheating the part with a hot air tool...it works pretty well with 3609.

SMD adhesive

Electronics Forum | Thu Sep 01 01:43:12 EDT 2005 | adlsmt

This is a bad situation and if you use (better to rework) adhesive that means it will work worse in your normal process(wont hold). Heat all the leads to reflow temp, twist (rotate)the part untill it breaks free. Most adhesives are not designed for t

adhesive on pads

Electronics Forum | Tue Apr 02 22:58:10 EST 2002 | davef

Whatever I've said, my intent has never been to insult you. Smack you yes, insult you no. True, you never said the word �strings� but you did say � * �� shouldn't I be able to expect enough green strength from my epoxy to hold 0603 caps in place wi

Re: Stenil printing adhesive

Electronics Forum | Wed Oct 14 13:52:59 EDT 1998 | Bill Schreiber

Dear Sanjay, An important issue involved when stencil printing adhesives vs. solder paste is: How do you clean the stencils after printing? Do you need two machines? Two chemistries? Two waste streams? What are the potential environmental impacts an

Aperture sizes for printing SMD adhesive

Electronics Forum | Fri Feb 19 03:57:48 EST 1999 | Mark Alder

Please could you suggest a recommended aperture sizes for printing of smd adhesives. Any recommendations on stencil thickness as well as stencil finish will be appreciated.

Re: Aperture sizes for printing SMD adhesive

Electronics Forum | Fri Feb 19 12:56:34 EST 1999 | Tony A

| Please could you suggest a recommended aperture sizes for | printing of smd adhesives. Any recommendations on stencil thickness as well as stencil finish will be appreciated. | Mark, talk to Irene Horvath at I Source Technical Services, Inc. Her

Pull test norm for adhesive smt.

Electronics Forum | Tue Aug 12 09:52:58 EDT 2014 | thiagofrego

Would like to know if some exists norm that refers the parameters for test of extraction (pull test) of components SMD using adhesive.

High Temp (96/4) adhesive cure time/temp

Electronics Forum | Thu Feb 22 22:04:33 EST 2001 | davef

Travis: I just checked. You're correct. It's a SMD-310, circa 1985 with a 12" wide mesh belt and a screamin' three zones of solder meltin' fury.

Re: Aperture sizes for printing SMD adhesive

Electronics Forum | Mon Feb 22 12:04:15 EST 1999 | Dave F

| Please could you suggest a recommended aperture sizes for | printing of smd adhesives. Any recommendations on stencil thickness as well as stencil finish will be appreciated. | Mark: About the only rule of printing adhesives is: Keep it off the

  1 2 3 4 5 6 7 8 9 10 Next

360 smd adhesive searches for Companies, Equipment, Machines, Suppliers & Information

Circuit Board, PCB Assembly & electronics manufacturing service provider

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
Circuit Board, PCB Assembly & electronics manufacturing service provider

World's Best Reflow Oven Customizable for Unique Applications
Solder Paste Dispensing

We offer SMT Nozzles, feeders and spare parts globally. Find out more
High Throughput Reflow Oven

High Precision Fluid Dispensers
Assembly Automation Technology

Original SMT Feeders and spares for Panasonic, Fuji , Yamaha, Juki , Samsung