Electronics Forum: 5

Re: 0201 components

Electronics Forum | Thu Feb 24 20:47:27 EST 2000 | Todd Woods

The camera is important. I found the only machine, granted this was a year ago, capable enough for volume production, was the KME CM-88. Our test had 1 mispicked device of 5,000,000 attemps and 0 misplacements.

digital video comparators

Electronics Forum | Tue Jul 10 08:45:12 EDT 2001 | stefwitt

There are several low cost vision systems ( under $ 5,000) on the market: http://www.dvtsensors.com" ,Keyence, Texas Instruments, Imagenation. If they can capture the image in one shot ( comparing with one good board ) depends on the camera resolutio

Mydata Hydra tool reference mark error

Electronics Forum | Wed May 08 11:20:24 EDT 2013 | amelby

Thanks for the info on the Hydra tubes that will be helpful. I found the answer from one of the Mydata techs. The Camera needs the hydra head to go slower then 1.9m/sec and the setting was at 1.8m/sec. They found out that even if the machine was set

Mydata Pick and place

Electronics Forum | Sun Aug 26 12:40:59 EDT 2001 | stefwitt

I would like to enter the discussion by tossing some numbers in. First of all I don�t like the 3 Sigma value. 3 Sigma are 2000 defects per mio. if I remember correctly. This means, if you have 200 components on the board, then every 10 boards have on

MY19 Randomly reboots the computer

Electronics Forum | Sun Mar 29 14:17:03 EDT 2020 | midast

Hi We have a MY 19 that just reboots the computer. It is like some just unplugged the power. We have nothing in the logs. All I see is when it starts up again. The problem can happen anytime. Today I found that it always happens when I try to auto

Re: Adhesive Dispenser Vs. Screen Printing Adhesives Pros and Cons

Electronics Forum | Thu Oct 12 22:16:59 EDT 2000 | Dreamsniper

Hi Guys, I'd like to share this to all of you...you can start playing with the rests...Stated prices, if not indicated, are in Aussie $ or Singapore $. Stencil Printing Adhesive Pros a) Less Capital Equipment Cost (Short Term). In reality it is f

Can anyone say NOT to use my reflow profile???

Electronics Forum | Wed Apr 21 18:24:13 EDT 2004 | pjohnson@volterra.com

Simple process - we use similar Kester solder brands of "no clean" low residue solder wick to clean our pads, then brush with isopropyl, and apply Kesters brand of tacky flux under a Leica 6x microscope. We do this on 7x7mm and 9x9mm packages. This w

Re: Wierd Tombstoning on Tant Caps

Electronics Forum | Fri May 01 20:12:29 EDT 1998 | Steve Gregory

| I've never seen this before. Today, I got this tombstoning on Tantalum Capacitors (Okay, I saw that before) | Here's the part that seems weird to me: | -They didn't tombstone onto a termination - they went onto their sides! That's right, both ter

Yamaha/Philips Model Number Cross References

Electronics Forum | Thu Jul 07 19:39:18 EDT 2005 | darby

This is a very difficult question to answer as it will depend greatly on your component mix. I will presume that the CSM 84VZ is of the following configuration: 2 x RDC Synchro Heads. Heads 1 & 2. These are mechanically centering heads with a chucki

  1  

5,000 sec camera searches for Companies, Equipment, Machines, Suppliers & Information

See Your 2024 IPC Certification Training Schedule for Eptac

Component Placement 101 Training Course
AI Data Center Hardware Manufacturing

High Precision Fluid Dispensers
PCB Handling with CE

Wave Soldering 101 Training Course
PCB separator

"回流焊炉"