Electronics Forum: air tweezer (Page 1 of 2)

Soldering Test Interview

Electronics Forum | Wed May 04 10:27:33 EDT 2005 | nice90

Or you can use the Hot Air (Hakko) to remove that component and a tweezer to pull it. dont pull it just yet. If you see the solder melting then feel the component using the tweezer by wiggling it a bit and if you can wiggle it only then you can pull

omit stencil apertures to hand solder or paste, reflow then solder.

Electronics Forum | Thu Feb 27 08:59:15 EST 2020 | spoiltforchoice

In both cases, it will depend on storage conditions, unless you do something horrible to them (or as previously mentioned, wash them) months & months. For boards we put through SMT and then stash for THT loading in smaller qty's I don't think we've e

Please HELP! Need to purchase a few machines

Electronics Forum | Fri Feb 01 02:32:31 EST 2019 | robl

It's nice to be able to do things in house, and it's good to have somewhere without commercial pressures to learn and make mistakes, so I can understand where you are trying to go. Those machines look a little lightweight for consistent quality pr

Re: SMT adhesive recomendation

Electronics Forum | Thu Jul 06 07:30:46 EDT 2000 | John

Ralph, Typically our co-op students put down solder paste with a syringe, place the parts on the paste with tweezers, and then reflow the paste with a hot air pencil. This works pretty well when they are hand building prototypes. You can probably

what to buy?

Electronics Forum | Mon Sep 21 01:57:55 EDT 2009 | kaz

Hello All, My first visit here. I own and operate a small Industrial & Consumer Electronics Service Shop. There is more and more modules with high density fine pitch SMDs that we cannot handle. We bought PACE ThermoFlow BGA SMD station with a bunch o

Die attach with solder paste

Electronics Forum | Wed Aug 28 10:16:12 EDT 2002 | Jim M.

Sam We install a lot of die in the SMT room using same process as SMT parts.Water soluble solder paste is used for attachment of die to ceramic and boards. Biggest problem i found is the adjustment from installing the die in the bonding area. The t

Re: Pre-heat for Ceramic Capacitors

Electronics Forum | Sat Mar 06 08:01:45 EST 1999 | Scott Cook

| Can someone please advise me to the rework procedure for removal and replacing Ceramic Chip Capacitors (e.g. 0805, 1206, etc.)? | | Is it necessary to pre-heat ceramic capacitors before soldering them onto a PCB with a soldering iron? Is this just

Multiple Resistor Rework

Electronics Forum | Mon Aug 30 11:09:13 EDT 2010 | davef

Lots of small parts, lots of hand soldering, lots of tired eyes inspecting on lots of boards: yields lots of room for error. How about this: * Part removal ** Cut each resistor between the pads using dykes ** Using a soldering iron [or hot air pen],

Re: Solderability of BGA and PCB

Electronics Forum | Mon Nov 27 19:32:02 EST 2000 | Michael Parker

Prof. Whoopee - amazing facts that you find on your 3-D BB, it has completely confounded my comrade, Chumley. Plainly spoken that around the SF Bay Area a.k.a. Silicon Valley(ever hear of the famous SF Fog?)during the winter months, near the coast a

Re: Solutions For Low Volume BGA/SMT Rework

Electronics Forum | Thu Feb 19 13:52:58 EST 1998 | mike c

| We are in need of a low cost system for the rework of | various SMT devices. Ideally the machine should support BGA, | SQFP, and large PLCCs. | Is it a dream to ask for SMT tweezers, a regular iron, | and a convection pencil as well? Want a machin

  1 2 Next

air tweezer searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling Machine with CE

Training online, at your facility, or at one of our worldwide training centers"
IPC Training & Certification - Blackfox

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
best pcb reflow oven

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
Win Source Online Electronic parts

Software for SMT placement & AOI - Free Download.
Hot selling SMT spare parts and professional SMT machine solutions

Private label coffee for your company - your logo & message on each bag!