Electronics Forum | Thu Mar 31 13:48:19 EST 2005 | shannond
Hi All, I have to solder a device with platinum clad nickel leads to a PCB. I am having a hard time getting solder to flow on to the leads. Are there special proceedures that I need to follow because of the platinum or am I just dealing with contamin
Electronics Forum | Fri Aug 17 01:40:55 EDT 2001 | V.RAMANAND KINI
We are in the watch & clock Business. We have a Watch IC chip that has to be wirebonded using Ultrasonic aluminium wedge bonder. The wire dia is 1.25mil. The PCB is made of G10 Glass epoxy copper clad laminate. The copper thickness is 18 microns. The
Electronics Forum | Thu Aug 12 11:00:42 EDT 2010 | hegemon
Without seeing a picture, my first instinct would be first and foremost some fixturing that provides full support for your print process. After that, since you are citing bow and twist, consider that the fixturing might as well travel through the ov
Electronics Forum | Thu Aug 12 14:17:19 EDT 2010 | mikesewell
You might reduce your panel size, cut it in half and rotate to better utilize your edge clamping/board supports. Tape off your current stencil and see if it improves the print. A new stencil and a little extra handling may be cheaper than tooling.
Electronics Forum | Wed Aug 11 18:35:17 EDT 2010 | julie1
Anyone work with or have knowledge about metal core/clad boards? The board I'm working with is approximately 2" X 3/4" aluminum core pcb, in a 56 up array. There are 3 LED placements per board. I'm having trouble getting a consistent screen print.
Electronics Forum | Sat Apr 30 11:34:23 EDT 2016 | huanyupcb
High Mix,Low Volume,Short Delivery PCB Supplier. 1.The world top 500 PCB supplier.( Samsung DELL Alcatel-Lucent Huawei Lenovo FOXCONN ASUS etc ) 2.Over 15+ Years of PCB Expertise. 3.Provided "PCB & Assembly One-stop shop"service,No MOQ. 4.ISO9001 I
Electronics Forum | Wed Apr 22 05:33:06 EDT 2015 | mbb
We'have been working on an issue regarding aluminium capacitor placement in PCB. In fact, we have twisted (shifted) capacitors. Through root causes analysis, we confirmed that this phenomenon is happening during reflow process (no issue on placement
Electronics Forum | Sat Jul 23 01:51:04 EDT 2022 | poly
You'll find a lot of guides for cutting aluminium on the internet but basically, try and use a bigger end mill if you can, keep it at the right speed (not slower). We cut 1.6mm aluminium with a 3mm end mill. Smaller end mills didn't evacuate the chip
Electronics Forum | Thu Jun 04 02:16:43 EDT 2020 | SMTA-Robert
Looking for CTE and young's modulus values for aluminum backed PCB for solder joint predictions. The data sheets are a bit sparse, and the weighted average method somehow doesn't feel appropriate. Any advice is welcome. Thanks!
Electronics Forum | Tue Jul 31 22:06:12 EDT 2007 | davef
We had no problems reflowing an assembly on Bergquist Thermal Clad. The assembly was small. So, we built it on a 8-up fixture. It stayed in the fixture from screen print, through pick and place, and into reflow. When the fixture came out of the r
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
.gif)
