 hitech.gif)
Electronics Forum | Fri Aug 17 01:40:55 EDT 2001 | V.RAMANAND KINI
We are in the watch & clock Business. We have a Watch IC chip that has to be wirebonded using Ultrasonic aluminium wedge bonder. The wire dia is 1.25mil. The PCB is made of G10 Glass epoxy copper clad laminate. The copper thickness is 18 microns. The
Electronics Forum | Sat Apr 30 11:34:23 EDT 2016 | huanyupcb
High Mix,Low Volume,Short Delivery PCB Supplier. 1.The world top 500 PCB supplier.( Samsung DELL Alcatel-Lucent Huawei Lenovo FOXCONN ASUS etc ) 2.Over 15+ Years of PCB Expertise. 3.Provided "PCB & Assembly One-stop shop"service,No MOQ. 4.ISO9001 I
Electronics Forum | Thu Apr 29 04:34:07 EDT 2004 | allsmt
Dear Sir's, we had become an inquiry from an customer of allSMT, who is in need of an Machine which can solder via Laser? does anybody has experience with this procedure? I will try to explain the project. The pcb is an Aluminium pcb. There must
Electronics Forum | Wed Apr 22 05:33:06 EDT 2015 | mbb
We'have been working on an issue regarding aluminium capacitor placement in PCB. In fact, we have twisted (shifted) capacitors. Through root causes analysis, we confirmed that this phenomenon is happening during reflow process (no issue on placement
Electronics Forum | Thu Nov 14 12:11:00 EST 2002 | V.RAMANAND KINI
I am looking for a reflective coating on PCB. I have designed a PCB with SMT type side LEDs and Top LEDs. The light from these LEDs fall on to a lens profile on top of these and get mangnified and reaches the dashboard instrument's pointers. I tried
Electronics Forum | Sat Jul 23 01:51:04 EDT 2022 | poly
You'll find a lot of guides for cutting aluminium on the internet but basically, try and use a bigger end mill if you can, keep it at the right speed (not slower). We cut 1.6mm aluminium with a 3mm end mill. Smaller end mills didn't evacuate the chip
Electronics Forum | Fri May 28 07:37:52 EDT 1999 | Steve Cheung
Yes l know this problem keeps cropping up on the forum but l've missed some of the follow-ups. Our problem is that the lifting only occurs on 3% of production so actually detecting an improvement is difficult. We're actually having to inspect 144 p
Electronics Forum | Mon Aug 16 14:43:44 EDT 2010 | dan_ems
Hello, i don't know if is possible to dispense paste but for reduction of cost we use a diferent type of stencils, from aluminium of 0,2 mm, purchased from a typography of newspapers. Ofcourse the pcb for what we use this stencil are simple. But th
Electronics Forum | Mon Jun 01 17:49:39 EDT 2009 | gregoryyork
Sorry looking at your profile again and considering its Aluminium substrate I would opt for an increase to the preheat or introduce a soak to the profile to get the PCB up to reflow. Try soaking between 175 - 200C sufficient enough to heat the whole
Electronics Forum | Mon Jul 11 16:07:27 EDT 2022 | madisreivik
You cannot use diamond cut routers on aluminium. They will clog up in seconds.. You have to use "endmill" type. These are available from all PCB drill/mill supplier, nothing fancy. Depaneling - you mean cutting only tabs, not full perimeter ?
Hitechpcba is a wоrld-lеаding PCB Manufacturing & PCB Assembly company with more than 20 years experience in the electronics manufacturing industry. We focus on Circuit board fabrication, PCB assembly, electronic parts sourcing.
3F, B5 Dong, Zhimeihuizhi, FuYong, Bao'an Dist.
Shenzhen, China
Phone: 008675529630063
