Electronics Forum: ams (Page 720 of 857)

Drawing / BOM Revisions

Electronics Forum | Fri Aug 02 12:57:38 EDT 2019 | aaronhodge

Hello All, I am a few months in with a new employer, spending much of my time with AS9102B First Article Inspections. This company is a Micro-Chip and PCA OEM but also designs, develops and manufactures products for a handful of customers, as well.

EPR software

Electronics Forum | Tue Aug 27 02:55:43 EDT 2019 | oxygensmd

I am looking for a simple software which I can use in my production. I have the following task which I would like to solve with this software: - Components storage: counting the components in my production area. I would like to store their following

GSM machine stops randomly; "BM" bus master light out

Electronics Forum | Wed Nov 27 08:54:03 EST 2019 | ttheis

Hi Tushar, Thanks for the reply. I do believe I put it into debug mode but I will be sure to check next time I try logicomm. I am not using any RAMTF or PTF. At the moment I have upgraded the machine from EPC-5 to EPC-5-66 which I found cheap. The

Correct size screwdriver bit for torquing M1.6 screw?

Electronics Forum | Fri Sep 27 13:34:34 EDT 2019 | tey422

We are to install a very small BGA socket, the datasheet noted to be torque the M1.6 size Phillips screw to the spec for installation. I couldn't find the correct size bit that would fit our torque screwdriver. Per the screw size, shouldn't it be PH0

mpm up2000 z axis hardware limit

Electronics Forum | Wed Dec 04 08:02:02 EST 2019 | proceng1

Contact George Castonguay at PPM. He is a Jedi when it comes to these machines. In fact, since you just got it, a good investment would be to have George come in and go through the machine and get it calibrated. 603-895-5112 They also sell parts

Automated or Semi-Automated Thermal Gel Application

Electronics Forum | Tue Oct 08 15:02:10 EDT 2019 | SMTA-Joe

Hello SMTA, I am looking into the possibility of automating, or semi-automating the application of thermal gel (THERMA-A-GAP GEL8010) onto the bottom of some power supplies installed in PCBs. As of now I will need to apply approx. 5 mils of this gel

SMEMA Interface minimum requirements

Electronics Forum | Fri Oct 18 15:29:16 EDT 2019 | kylehunter

Hi all. We are currently trying to build a downstream bypass to have our final conveyor feed into our oven, which doesn't have a SMEMA interface. Right now we have to manually connect the two downstream ready pins by hand. I have a good idea of how I

Soldering Issue in Sensor component

Electronics Forum | Fri Dec 27 12:47:21 EST 2019 | ameenullakhan

Dear Team, We are facing open solder issue in a sensor component. Rejection rate is 2 out of 50 components placed. The issue is very random. We have tried increasing the solder paste height from 5 mil to 7 mil. The issue persist still. Differen

SMT Samtec dual edge connector assembly help

Electronics Forum | Wed Jan 08 16:27:11 EST 2020 | rmitchell

We have a PCB with the dual sided connector that slides on from the edge and has leads on the top and bottom sides of the PCB. It has 20 leads on each side of the PCB with with about .8mm pitch. The PCB also has a gold grounding strip on the edge fo

solder balls/wash

Electronics Forum | Thu Jan 09 13:18:15 EST 2020 | charliedci

We have been experiencing an issue with solder balls coming out of wave, both RoHS and 63/37, no clean process. It has been determined that a reduction in flux has all but eliminated the solder balls except for where we need to use board stiffeners a


ams searches for Companies, Equipment, Machines, Suppliers & Information