Electronics Forum: bent leads problem correction (Page 1 of 28)

QFP bent leads

Electronics Forum | Thu Mar 02 12:08:59 EST 2017 | rvines1

We usually receive them in batches of a few hundred, and occasionally from catalog vendors like Mouser. Inspection has been inconclusive. They don't have to be bent much to cause a problem. I'm wondering if it's just the nature of the beast.

QFP bent leads

Electronics Forum | Thu Mar 02 10:09:02 EST 2017 | rvines1

We have a board with an LQFP-176 with 0.5mm pitch. We regularly have to rework these due to unsoldered pins, which is due to pins that are slightly bent upward. We believe that we are receiving them this way, but it may also be due to handling on o

Re: Reclaim - bent leads (SMT)

Electronics Forum | Thu Aug 27 19:46:21 EDT 1998 | Kallol Chakraborty

Thanks very much. | Kc, | Bent leads are a major defect driver for us, and despite much research I have yet to find a lead straightening device which is not labor intensive. I do however have some limited information about a machine called the "Top

Re: Reclaim - bent leads (SMT)

Electronics Forum | Mon Aug 24 08:29:05 EDT 1998 | Chris Fontaine

Kc, Bent leads are a major defect driver for us, and despite much research I have yet to find a lead straightening device which is not labor intensive. I do however have some limited information about a machine called the "Top Form 2020" by Polytool

Hitachy QFP 256 leads problems

Electronics Forum | Tue Mar 20 00:02:00 EDT 2007 | Darby

Some causes of skewing. If you have exhausted all mechanical problems for that head. Pickup data from tray is incorrect. If you aren't picking up in the exact centre it is possible that the component is being skewed after vision adjustment i.e. cent

Rad 5 performance: bent lead

Electronics Forum | Tue Jul 09 15:40:06 EDT 2019 | assuredtech

That's a great point about air consumption, don't reduce the 1/2 inch air line requirement, meet the CFM air requirement and of course dry shop air. Check the Auto oiler for the CTA is running correctly, 5W 30 NON Detergent oil only. Attached is a pi

Rad 5 performance: bent lead

Electronics Forum | Mon Jul 08 18:45:53 EDT 2019 | assuredtech

Would you happen to have the Jig used to check that the component itself is in spec with UIC's general specifications? 1.) Component in spec. 2.) Correct 2.5mm pusher on the feeder / dispense head. Also set the conditioner guide where the comp enter

Rad 5 performance: bent lead

Electronics Forum | Mon Jul 22 10:29:37 EDT 2019 | slthomas

Thanks for adding that, Daniel! It always helps the rest of us when the solution to a problem is published. Plus, my brain won't rest until I know.

Rad 5 performance: bent lead

Electronics Forum | Tue Jul 09 07:35:48 EDT 2019 | stephendo

Watch the air pressure gauge and make sure you have a good steady air pressure. I don't know about the Rad 5 but the Rad 3 was sensitive to fluctuations in air pressure. By any chance do you have a VCD running nearby when you are having the problems?

Rad 5 performance: bent lead

Electronics Forum | Mon Jul 08 12:21:17 EDT 2019 | slthomas

I forget which type of CTA that machine has so I probably won't be much help. It's been ages since I worked on them but it doesn't look like you'll find many people that have. That said, usually if you get things aligned properly and it still bends

  1 2 3 4 5 6 7 8 9 10 Next

bent leads problem correction searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

High Precision Fluid Dispensers
Solder Paste Dispensing

Best Reflow Oven
High Throughput Reflow Oven

World's Best Reflow Oven Customizable for Unique Applications
AI Data Center Hardware Manufacturing

We offer SMT Nozzles, feeders and spare parts globally. Find out more