350 best led pick & place maskin results

Electronics Forum: best led pick & place maskin (Page 5 of 35)

Pick and place machine for small productions. Any suggestions?

Electronics Forum | Wed Sep 18 19:38:33 EDT 2013 | jvadillo

Hi all! after hours of manual hand soldering and after spending thousands of euros subcontracting PCB assembly, we have decided to buy a fully automated pick&place machine. Our main assembly requirements are 0805/0603 for passives and TQFP-64

Pick and place machine for small productions. Any suggestions?

Electronics Forum | Thu Sep 19 15:06:39 EDT 2013 | jvadillo

We have already one desktop oven and a manual stencil printer. And we have a quite complete soldering bench with several JBC tools. We also have stock for all active elements we use. We normally relay on the PCB assembler to provide the passive comp

Topaz X large component sequencer pick causes outside soft limit error

Electronics Forum | Wed May 06 20:52:26 EDT 2015 | arbpkevin

I have been using my topaz X for about 4 years now and I feel that I am fairly knowledgeable about it, at least the functions of it that I use... I am trying to use the LCS to place some qfp chips on a new product and I have set the whole thing up t

LED Pick up Issues during Feeder Feeding

Electronics Forum | Wed Mar 13 09:11:48 EDT 2013 | smt_guy

Hi All, Need your advice / help. We have assembleon pick-and-place machines and we got some pick-up issues on certain LED's that are Dome Type. The LED's get off from the tape pocket during feeding due to the dome of the LED sticks on the tape surfa

SMD LEDs stick to nozzle while mounting

Electronics Forum | Sun May 20 00:11:45 EDT 2012 | kiss

We are mounting 3528 package LEds with pick & > place machine.The problem is , nozzle picks up > the LED , but it stick to the nozzle & not > placed. Then it gives error in the next cycle. > Can anybody suggest the solution? Please advise on mo

SMD LEDs stick to nozzle while mounting

Electronics Forum | Sat May 19 04:09:17 EDT 2012 | gme

We are mounting 3528 package LEds with pick & place machine.The problem is , nozzle picks up the LED , but it stick to the nozzle & not placed. Then it gives error in the next cycle. Can anybody suggest the solution?

SMT before through-hole

Electronics Forum | Tue Aug 14 10:53:15 EDT 2007 | rgduval

Should be do-able. Check out a couple of things: 1. Temperature tolerance of the LED's. If they can't withstand reflow, then you won't be able to do it. 2. Height of the LED's versus the travel of your pick/place. If your pick/place head won't t

LED sticking into carrier tape

Electronics Forum | Tue Aug 01 09:27:13 EDT 2017 | tmennink

Hi all, We are having a lot of trouble with mis-pick trying to place silicone dome LEDs(3535 package) It seems that the silicone of the LEDs is sticking to the side wall of the carrier tape pocket. The vacuum nozzle would normally suck up the led an

Placing Luxeon Rebel

Electronics Forum | Tue Mar 30 17:52:15 EDT 2010 | cusackmusic

They are very finiky. If you have good solder paste, and a slight down pressure, to make sure the LED is "stuck" to the board, you should be able to place it. Pick it up on the center of the flat, NOT the lens. Even with the vacuum turned off, t

Panasonic CM Nozzle shifts LED's positions

Electronics Forum | Sun Apr 17 00:04:03 EDT 2022 | klauss

I am mounting 3535 Cree High-power leds with p&p machine. First nozzle picks up the led normally and then it's placed good but after 4-5 times nozzle picks up the led like at an angle. looks like it holds the led from the side edge of the dome.