Electronics Forum | Fri Aug 22 00:20:29 EDT 2008 | rameshr
Hai, In our process we are using the micro bga of size 13X13mm of pitch 0.45mm,after soldering process the bga found collapsed, we absorbed that the PCB land pattern of the BGA was not in array, uneven distribution of pads (area) & most of the pads
Electronics Forum | Mon May 25 08:37:28 EDT 2009 | d0min0
Hello, recently we changed supplier of the LF BGA, we did corossection and now have doubts... previous BGA specs : pitch 1mm, ball diameter 0.6mm future BGA specs : pitch 1mm, ball diameter 0.4mm on the crossecrion we found that one of the ball seem
Electronics Forum | Wed Mar 02 06:19:03 EST 2005 | pjc
Go to http://www.ipc.org and look up IPC-7351 - Generic Requirements for Surface Mount Land Pattern and Design Standard The successor to the IPC-SM-782A is here! The document covers land pattern design for all types of passive and active components
Electronics Forum | Tue Sep 21 13:12:56 EDT 1999 | Dave F
| My stencil thickness is 6 mil and we got qfp's with fine pitch. | how many percent should i reduce my stencil aperture using a 6 mil stencil for 0.5 mm pitch and 0.4 mm pitch ? | | thanks | Greg: I was going to link you to the IPC land pattern c
Electronics Forum | Thu Nov 07 10:59:11 EST 2002 | pjc
IPC-7525 "Stencil Design Guidelines" is a good reference document to have. Here are notes from a Tessera, (a major mBGA mfg.), study- "Application Note Solder Stencil Requirement for mBGA" The stencil aperture is to be square, equal in size to the l
Electronics Forum | Wed Jul 30 00:47:10 EDT 2014 | matusov
Hello gurus, I am a hardware designer with a small company. We are about to send a new PCB for fabrication. This board uses dozens of tiny QFN, DFN, and similar packages. As a final check I have been going through the datasheets of all these parts t
Electronics Forum | Wed Feb 07 09:46:20 EST 2001 | pjc
I need some guidance here. I've got a new board w/ a FBGA-48 package, Samsung CMOS SRAM. It's a full matrix BGA w/ 0.30mm-0.40mm ball diameter @ 0.75mm pitch. Balls are eutectic. PCB land diameter is 0.4mm. There are TSOP I 0.5mm lead pitch component
Electronics Forum | Mon Aug 02 18:46:33 EDT 1999 | Jim Blankenhorn
| | Has anyone done the research on BGA pad size? suppose I have a 0.030" diameter pad as recommended pad size from the spec, what will the minimum pad size allowed? We are laying out a high density board. | | If you know what component your'e going
Electronics Forum | Wed Sep 22 21:12:16 EDT 1999 | se
| | | | My stencil thickness is 6 mil and we got qfp's with fine pitch. | | | | how many percent should i reduce my stencil aperture using a 6 mil stencil for 0.5 mm pitch and 0.4 mm pitch ? | | | | | | | | thanks | | | | | | | We use 6 mil lasercu
Electronics Forum | Wed Sep 22 22:23:55 EDT 1999 | SY
| | | | | My stencil thickness is 6 mil and we got qfp's with fine pitch. | | | | | how many percent should i reduce my stencil aperture using a 6 mil stencil for 0.5 mm pitch and 0.4 mm pitch ? | | | | | | | | | | thanks | | | | | | | | | We use 6
