Electronics Forum | Mon Dec 17 12:06:58 EST 2007 | pjc
5 Steps to Eliminate Bridges: 1. Establish (wave) Parallelism First and foremost, you must establish board-to-wave parallelism. This is the prerequisite to any wave solder process control. For an understanding of the power of this approach go to ht
Electronics Forum | Mon Dec 17 11:55:08 EST 2007 | chef
I recently had the same problems, solder bridges on every thing I made, different customers boards, etc. I wave with no-clean flux. As I sorted out problems (pin holes, blow holes, splatter, etc.) I found a lot of variable factors. I changed flux,
Electronics Forum | Tue Jun 08 08:40:37 EDT 1999 | Wister
Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl
Electronics Forum | Tue Jun 08 08:38:15 EDT 1999 | Wister
Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl
Electronics Forum | Tue Jun 08 12:49:41 EDT 1999 | Dave F
| Hi,my master | How to iron out such soldering bridge with below conditions: | 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. | 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB | 3.using spraying fluxer and n
Electronics Forum | Tue Jun 08 13:06:53 EDT 1999 | Kevin Hussey
| | Hi,my master | | How to iron out such soldering bridge with below conditions: | | 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. | | 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB | | 3.using spraying fl
Electronics Forum | Tue Jun 08 17:52:53 EDT 1999 | Chrys Shea
| | | Hi,my master | | | How to iron out such soldering bridge with below conditions: | | | 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. | | | 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB | | | 3.using s
Electronics Forum | Thu Nov 17 21:46:48 EST 2005 | C. Kolokoy
With DIP type components, a sub-par fluxing method (foaming a no-clean), and a chip wave where one is not needed are formulas for bridging and insufficient wetting. If you have SMD's on the wave solder side of the board greater than 0603, and no SOT
Electronics Forum | Sun Aug 13 22:26:01 EDT 2017 | dawson
Anyone who knows how to prevent such > flaw? > > Tombstones are those lifted components > from one sides. This results in costly and > time-consuming amounts of touch-up and re-work > after the assembly is completed. For the > customers, this e
Electronics Forum | Wed Sep 18 18:41:17 EDT 2002 | davef
People have made good comments. Additional points are: * Your bridging is probably being caused by one or more of the following: [1] printing too much paste, [2] smearing the paste during placement or subsequent handling, or [3] paste slump during t
