Electronics Forum: can (Page 2112 of 2414)

Another AOI thread

Electronics Forum | Mon Jun 18 07:07:35 EDT 2012 | buckcho

Thank you for the response, but the machine selection is not made by me, I only evaluate the machines. So two days ago I visited a company that has a Viscom AOI. I had good impressions about the machine but there were couple of things I didn't like:

Mydata MY15 Y-Wagon

Electronics Forum | Thu Jun 14 00:10:18 EDT 2012 | tech1

Most of it depends upon the type of Y wagon you have. if they are internal conveyors you need to remove the covers from the operator side. There are 3 screws holding the Y wagon down, 2 of them are hex screws and the one in front is an allen head. W

General ROI (Return on Investment)

Electronics Forum | Mon Jun 11 17:14:13 EDT 2012 | mmjm_1099

1st Question I am working on ROI for a bare board destacker and wondering if anyone has a general guideline to follow. Example of ROI for bare board destacker I have now as follows: $7500 for destacker, Avg panel input 3365, Time to load in panel 7

AOI Bench top

Electronics Forum | Wed Jul 04 11:55:23 EDT 2012 | tony_d

We are a low to mid range manufacturer as well. I looked at several different vendors incuding; Mirtec, Viscom, Marantz, Omron, VI Tech, Orbotech and Yestech. We selected Mirtec. As a mid range manufacturer, one of my main concerns was quick and eas

Selective Soldering Issues

Electronics Forum | Thu Jun 21 16:30:47 EDT 2012 | grauen06

We are currently using an ACE K.I.S.S. 104. We used SN100 solder with AIM NC265 flux (no clean, alcohol-based). Also, we use topside preheat at 100 degrees C and a 6mm nozzle (as big as we can go with this application). The PCB has a matte finish as

Selective Soldering Issues

Electronics Forum | Fri Jun 22 21:07:08 EDT 2012 | tank1266

I have had Selective issues such as yours on two very different Selective Solder Machines. I was able to eliminate these issues by using Alpha EF-9301 wave flux with any SAC305 solder. It's a more aggressive flux, but really made the difference. Anot

Fuji CP IV-3

Electronics Forum | Wed Jul 04 10:17:18 EDT 2012 | daxman

Good morning, Just a few questions to clarify: 1. You backed up your machine proper data. 2. You upgraded Fuji Flexa. 3. You re-transmitted the proper data 4. Now, components are not placing properly? Do you have a fuji 96-001 calibration board? Ha

Soldermask - sulfur presence

Electronics Forum | Mon Jun 25 03:52:24 EDT 2012 | awtm

Our Customer had detected tarnished pad on ImAg PCBA and had conducted several SEM-EDX test at the soldermask below some of the chip resistors. High concentration of sulfur was found and it can be significantly reduced after further chemical cleaned

QFN aligment issues

Electronics Forum | Fri Jun 29 10:56:56 EDT 2012 | jorge_quijano

Hi guys, I need your advise on this, I have a very uncommon PCB design (at least for me, I've never seen anything like this...) it is 32" x 18" x 0.062" and has 9 QFNs that are driving me crazy, I'm not able to get a good alignment, I can get a mediu

Phillips Topaz LED intensity

Electronics Forum | Thu Jul 05 20:54:27 EDT 2012 | actioncontrols

Hello: We have used our Phillips Topaz on a number of volume jobs and been very pleased. A while ago it became apparent that the vision LED's were growing dimmer as evidenced by having to adjust light intensities upward for various components in so


can searches for Companies, Equipment, Machines, Suppliers & Information