Electronics Forum: can (Page 2113 of 2415)

AOI Bench top

Electronics Forum | Wed Jul 04 11:55:23 EDT 2012 | tony_d

We are a low to mid range manufacturer as well. I looked at several different vendors incuding; Mirtec, Viscom, Marantz, Omron, VI Tech, Orbotech and Yestech. We selected Mirtec. As a mid range manufacturer, one of my main concerns was quick and eas

Selective Soldering Issues

Electronics Forum | Thu Jun 21 16:30:47 EDT 2012 | grauen06

We are currently using an ACE K.I.S.S. 104. We used SN100 solder with AIM NC265 flux (no clean, alcohol-based). Also, we use topside preheat at 100 degrees C and a 6mm nozzle (as big as we can go with this application). The PCB has a matte finish as

Selective Soldering Issues

Electronics Forum | Fri Jun 22 21:07:08 EDT 2012 | tank1266

I have had Selective issues such as yours on two very different Selective Solder Machines. I was able to eliminate these issues by using Alpha EF-9301 wave flux with any SAC305 solder. It's a more aggressive flux, but really made the difference. Anot

Fuji CP IV-3

Electronics Forum | Wed Jul 04 10:17:18 EDT 2012 | daxman

Good morning, Just a few questions to clarify: 1. You backed up your machine proper data. 2. You upgraded Fuji Flexa. 3. You re-transmitted the proper data 4. Now, components are not placing properly? Do you have a fuji 96-001 calibration board? Ha

Soldermask - sulfur presence

Electronics Forum | Mon Jun 25 03:52:24 EDT 2012 | awtm

Our Customer had detected tarnished pad on ImAg PCBA and had conducted several SEM-EDX test at the soldermask below some of the chip resistors. High concentration of sulfur was found and it can be significantly reduced after further chemical cleaned

QFN aligment issues

Electronics Forum | Fri Jun 29 10:56:56 EDT 2012 | jorge_quijano

Hi guys, I need your advise on this, I have a very uncommon PCB design (at least for me, I've never seen anything like this...) it is 32" x 18" x 0.062" and has 9 QFNs that are driving me crazy, I'm not able to get a good alignment, I can get a mediu

Phillips Topaz LED intensity

Electronics Forum | Thu Jul 05 20:54:27 EDT 2012 | actioncontrols

Hello: We have used our Phillips Topaz on a number of volume jobs and been very pleased. A while ago it became apparent that the vision LED's were growing dimmer as evidenced by having to adjust light intensities upward for various components in so

Question about Cost

Electronics Forum | Mon Aug 06 14:44:07 EDT 2012 | joefosho

Hey guys, I'm new to this forum and registered to ask a question about PCB assembly cost. I was hoping to design a PCB that will be approximately 6" by 6" with about 1100 0805 SMD components on it. Half of them being resistors (3 different values) a

Paste Printing Problems - Toshiba SSM3K15CT(TPL3) FET CST3 package

Electronics Forum | Mon Aug 13 12:38:38 EDT 2012 | grahamcooper22

Maybe the area ratio between the sides of the stencil apertures and the aperture opening is too low for the spec of the paste ? So it will tend to stick in the apertures. ...only solution is thinner stencil or a paste that can release easily when are

Quad IVc Part rejection issue

Electronics Forum | Wed Aug 15 16:15:51 EDT 2012 | derekj

Hello all. I'm having a bit of an issue with my IVc that's driving me insane. On occasion when placing a part, the machine will consistently reject the part 3 times before adjusting and then pick and place the part with no issues. I've done everythi


can searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling Machine with CE

Software for SMT placement & AOI - Free Download.
SMT spare parts - Qinyi Electronics

Best Reflow Oven
Online Equipment Auction of Altronic: Small-Batch Surface Mount & Assembly Facility

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.