Electronics Forum | Tue Apr 09 16:19:37 EDT 2002 | Peter L.
Has anyone built using the ALIVH PCB (0402, 0.8mm pitch uBGA) on the SMT line? I would like to know any process issues (paste printing, p&p, reflow) related to processing this pcb. Specifically, what type of solder paste was used (no clean) and wha
Electronics Forum | Fri Oct 19 13:04:14 EDT 2007 | brulal1
Thank Rob those are our own product, try few test by not clean some PCB never had any issue except on compoment under faraday cage. Did you know any norm that could persuade my boss and the R&D department that cleanning no clean is a waste of time. T
Electronics Forum | Fri Oct 19 10:49:48 EDT 2007 | brulal1
Hi I will like to know what do you think about cleaning hand solder, my employee spend about 25% of they time to brush they hand solder with teddy pen cleaner, we used no clean solder wire. It�s not been the first time that I try to eliminate those c
Electronics Forum | Fri Dec 15 11:06:06 EST 2006 | Gman
Hello All, Is Ionic Cleanliness testing using say an Ionograph on No-clean assemblies a valid test? If not, why? I understand factors like PCB cleanliness but is the 1.56ug/in2 IPC criteria valid for no-clean assemblies and can an Ionograph be used
Electronics Forum | Thu May 26 19:32:13 EDT 2005 | Mike Konrad
Three popular methods: Resistivity of Solvent Extract (ROSE) Test Method IPC-TM-650 2.3.25: The ROSE test method is used as a process control tool to detect the presence of bulk ionics. The IPC upper limit is set at 10.0 *g/NaCl/in2. This test is p
Electronics Forum | Thu Sep 05 18:15:15 EDT 2002 | pjc
There are chemistries out there that will solublize some post-solder NC flux residues. I have had success with Zestron material Vigon A200 and Petroferm material Hydrex DX. Go to http://www.zestron.com and http://www.petroferm.com These are chemical
Electronics Forum | Thu Jan 16 05:42:18 EST 2003 | nifhail
I've a query. I have one new Customer whom insisted us to use RMA paste on their product. The problem is, on some of their products they use via hole as the test point in where all the PCB finished are ENTEK and as usual I have to print solder paste
Electronics Forum | Wed Aug 10 08:10:39 EDT 2005 | davef
Comments are: * Sounds like it's necessary to clean "heareous F381, F352 no clean solder paste" in your application. Consider a paste that may be better suited to your application. * If you're cleaning "low residue flux", consider using an organic ac
Electronics Forum | Mon Aug 22 11:50:02 EDT 2011 | rway
Yes, but even high force probes are not a cure-all. You still get flux build-up over time which can cause contact issues. The best way is to use a low residue flux in the wave to minimize what's left on the pcb post-wave.
Electronics Forum | Tue Jul 02 12:33:32 EDT 2002 | Mike Konrad
We have had success removing white residue. A change of chemical (PCB-Wash or Vigon A200) have a good track record in removing white residue. As Dave stated, we (and others) operate a contract cleaning service. Contact me offline and I�ll provide
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
