Electronics Forum: cure and soldermask and clean (Page 1 of 3)

seperation of soldermask and pcb

Electronics Forum | Wed Mar 19 08:38:13 EDT 2014 | davef

I can't picture much of what you're saying, not for nothing, I'm just not connecting. During assembly, solder mask can affected by heat and chemicals. Typically this would be during: * Soldering * Cleaning I will tell you this: Not to defend assem

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 13:55:05 EDT 2014 | horchak

Ok lets put it this way. If the PCB house used a high quality mask and properly applied it to a properly cleaned surface and properly cured it, then as Dave stated above there are only two things that can destroy it. Excessive heat and overly aggress

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 08:29:33 EDT 2014 | sara_pcb

Please refer the attached jpegs, The problem is noticed after reflow soldering followed by conventional through hole soldering. Flux used one is MIL Std. Brush cleaning in IPA is followed after each soldering step. regards, R.Saravanan

Discoloring of Soldermask and silkscreen

Electronics Forum | Mon Apr 12 19:28:26 EDT 1999 | Tom B

Netters, When I reflow a PCB there is a discoloration of silkscreen and mask. It appears if Profile is too hot! But I dont think so, maybe I'm wrong? 1. Kester 293 no clean 2. 2.1 C/s for 30s to 150 C 3. .5 - .7 C/s for 60s to 185 C 4. 1.5 C/s u

Cracking Capacitors and Solder Balls

Electronics Forum | Mon Jun 08 14:19:30 EDT 1998 | Gary Simbulan

Earl, et al, Boy things get old and cold around here fast. I promised more detail on my capactior problem and I thought I could drop something completely different in the same message and tell a tale of solder balls. First the caps. We still have

No Clean and Underfill

Electronics Forum | Fri Mar 19 10:27:42 EDT 2010 | karlo

No clean pastes leave more flux residues. These can result in void formation and inhibtion of underfill curing. Selection of an underfill that is compatible with the flux residue is important. One company that has written about the effect of flux

COB and wire bond

Electronics Forum | Mon May 07 22:29:52 EDT 2001 | davef

4 wire per sec ... you figure how many you need] Encapsulation ~$120K for a dispenser [10 sec per die ... you figure how many you need] plus a cure oven ~$100k Throw in a another ~$100k for marking and cleaning Check the September 2000 SMTnet New

Re: Discoloring of Soldermask and silkscreen

Electronics Forum | Mon Apr 19 11:21:03 EDT 1999 | Travson

| Netters, | | When I reflow a PCB there is a discoloration of silkscreen and mask. It appears if Profile is too hot! But I dont think so, maybe I'm wrong? | | 1. Kester 293 no clean | 2. 2.1 C/s for 30s to 150 C | 3. .5 - .7 C/s for 60s to 185

Re: Discoloring of Soldermask and silkscreen

Electronics Forum | Tue Apr 13 18:11:00 EDT 1999 | Jimmy Strain

| Netters, | | When I reflow a PCB there is a discoloration of silkscreen and mask. It appears if Profile is too hot! But I dont think so, maybe I'm wrong? | | 1. Kester 293 no clean | 2. 2.1 C/s for 30s to 150 C | 3. .5 - .7 C/s for 60s to 185

Re: Discoloring of Soldermask and silkscreen

Electronics Forum | Mon Apr 19 20:49:13 EDT 1999 | Dave F

| Netters, | | When I reflow a PCB there is a discoloration of silkscreen and mask. It appears if Profile is too hot! But I dont think so, maybe I'm wrong? | | 1. Kester 293 no clean | 2. 2.1 C/s for 30s to 150 C | 3. .5 - .7 C/s for 60s to 185

  1 2 3 Next

cure and soldermask and clean searches for Companies, Equipment, Machines, Suppliers & Information

SMT feeders

High Resolution Fast Speed Industrial Cameras.
One stop service for all SMT and PCB needs

Easily dispense fine pitch components with ±25µm positioning accuracy.
High Throughput Reflow Oven

High Throughput Reflow Oven
convection smt reflow ovens

World's Best Reflow Oven Customizable for Unique Applications
Fully Automatic BGA Rework Station

"回流焊炉"