Electronics Forum: cyberoptics laser align (Page 1 of 16)

quad align init problem

Electronics Forum | Thu May 20 10:01:23 EDT 2010 | jmw

Just a slight correction....the quad align card is located at the back rear right of the machine (in a cage). If it is a cyber-optics 4c machine....the laser align card is in the front card rack to the far left.

Quad 4C laser align calibration

Electronics Forum | Thu May 26 09:21:37 EDT 2016 | bobpan

Everytime I have seen an offset like that it was dirt on the quad-align lens.....try cleaning it off with alcohol and a lint free cloth. If this does not fix it....you may have dirt inside the quad align itself. I am assuming you have checked to ma

Quad 4C laser align calibration

Electronics Forum | Thu May 26 15:13:47 EDT 2016 | bobpan

If there is dust (on the glass) off from the center of the lens it will add it to the part when scanning it and place off. I have ran into this twice.....I fixed it once by breaking the lens on the quad align and blowing it out.....another time I hel

Quad 4C laser align calibration

Electronics Forum | Thu May 26 15:16:28 EDT 2016 | bobpan

oh ya....i forgot....to verify this....turn off all the extents for the parts and just pick them and place them....if they are very close to where they should be then it is the quad align causing the problem....this is how you can verify it. Copy the

Quad 4C laser align calibration

Electronics Forum | Thu May 26 17:45:36 EDT 2016 | stevedc

Thanks for the thoughts. I will try a few things tonight so see if I can clean anything from the windows. As always, thanks for your thoughts and time :) BR, Steve

Quad 4C laser align calibration

Electronics Forum | Fri May 27 09:27:56 EDT 2016 | bobpan

Glad I can help....if you have any other questions...go to my web page @ www.precision-repairs.com Bob

Quad 4C laser align calibration

Electronics Forum | Fri May 27 00:18:15 EDT 2016 | stevedc

Soooo.... I started to take the laser off last night to clean it and decided to put it back on to do some more measurements to see if anything obvious turned up and lo and behold it is not good !!! Most likely cause I can think is that you were righ

Quad 4C laser align calibration

Electronics Forum | Wed May 25 22:32:28 EDT 2016 | stevedc

So, I haven't used my Quad 4C for a while and when I started everything back up to run a new board it appears that the Quad align is in need of calibration. When I pick up a component and do an LAE measurement on it it shows the part center location

Quad 4C laser align calibration

Electronics Forum | Thu May 26 14:06:03 EDT 2016 | stevedc

I did clean both lenses from the outside and checked all the MOD codes. I even removed the battery to reset everything and re-programmed all the codes but to no avail. I will strip it down and fully clean it to see if that helps. Just strange that

Samsung CP40 laser question

Electronics Forum | Fri Aug 07 13:03:53 EDT 2020 | assuredtech

SMT Forum, Does anyone know if the Sanyo laser alignments can be replaced with the Cyberoptics brand? If so is it plug and play or does it require any software or machine configuration changes. Thanks in advance

  1 2 3 4 5 6 7 8 9 10 Next

cyberoptics laser align searches for Companies, Equipment, Machines, Suppliers & Information

Win Source Online Electronic parts

Software for SMT placement & AOI - Free Download.
Sell Used SMT & Test Equipment

High Throughput Reflow Oven
Circuit Board, PCB Assembly & electronics manufacturing service provider

World's Best Reflow Oven Customizable for Unique Applications
Software for SMT

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
PCB separator

Internet marketing services for manufacturing companies